Wacker Neuson DT10 Track Dumper Index:

1 Operation
1.1 Information on this service manual
1. 2 Identification of warnings and dangers
1. 3 Designated use and exemption from liability
1.4 Overall view of vehicle
1.5 Brief description
Definition of operator’s control stand
1.6 Type labels and component numbers
1.7 Maintenance prop
Maintenance strut for high-tip skip
Maintenance strut for high-tip skip
Maintenance prop for front skip
Maintenance strut for swivel skip
2 Technical data
2.1 Chassis
2.2 Diesel engine
2.3 Diesel engine EPA Tier 4 (Opt.)
2.4 Hydraulic system
2.5 Travel gear
2.6 Working hydraulics
2.7 Electrical system
2.8 Tipping trailer
2.9 Front tip skip for lightweight load (optional)
2.10 High-tip skip (option)
2.11 High-tip skip (option)
2.12 Self-loading equipment (option)
2.13 Front skip (option)
2.14 Swivel skip (optional)
2.15 Noise levels
2.16 Vibration
2.17 Fuses
2.18 Dimensions model DT10 with skip
2.19 Dimensions of model DT10 with front tip skip for lightweight material (optional)
2.20 Dimensions model DT10 with high-tip skip (option)
2.21 Dimensions model DT10 with high-tip skip (option)
2.22 Dimensions model DT10 with front skip (option)
2.23 Dimensions for model DT10 with swivel -tip skip (option)
2.24 General tightening torques
Tightening torques for hydraulic screw connections (dry assembly)
Tightening torques for high-resistance threaded fittings
3 Maintenance
3.1 Fluids and lubricants
3.2 Maintenance plan DT10
3.3 Introduction
3.4 Fuel system
Specific safety instructions
Checking the fuel level
Refueling
Drain fuel
Stationary fuel pumps
Diesel fuel specification
Cleaning the filter cup/replacing the filter cartridge
Bleeding the fuel system
3.5 Engine lubrication system
Checking the oil level
Adding engine oil
Drain engine oil
Replacing the oil filter cartridge
3.6 Air filter
Replacing the filter
3.7 Hydraulic system
Specific safety instructions
Checking the hydraulic oil level
Adding hydraulic oil
Drain hydraulic oil
Replacing the hydraulic oil filter cartridge
Replacing the cartridge of hydraulic oil intake filter
Hydraulics cooling system
Specific safety instructions
Cleaning the oil/water radiator
Checking the coolant level/adding coolant
Draining coolant
Important information on the use of biodegradable oil
Checking hydraulic pressure lines
3.8 Tracks
Check track tension
Tightening the tracks
Decreasing track tension
3.9 Electrical system
Specific safety instructions
Servicing and maintenance at regular intervals
Instructions concerning specific components
Alternator
Battery
Battery master switch
3.10 General maintenance
Cleaning
General instructions for all areas of the vehicle
Exterior of the vehicle
Engine compartment
Threaded fittings and attachments
Pivots and hinges
3.11 Diagram of grease nipples DT10 with skip. Front tip skip for lightweight load (optional)
3.12 Overview of grease nipples DT10 with high tip skip (option)
3.13 Overview of grease nipples DT10 with front skip (option)
3.14 Overview of grease nipples DT10 with swivel skip (option)
3.15 Test report DT10
4 Engine
4.1 Engine overview
4.2 Checking and adjusting valve clearance
4.3 Checking and adjusting maximum engine speed
4.4 Fan belts: checking tension and replacement
Checking the tension of the fan belt
Fan belt damage and wear and tear
Fan belt replacement
4.5 Engine malfunctions
5 Traveling drive
5.1 Traveling drive pump DT10
5.2 Legend: traveling drive pump DT10
5.3 Hydraulic motor
5.4 Test instructions
Checking travel pressure DT10
Checking boost pressure DT10
Checking the adjustment and zero position of the pumps DT10
Checking straight-ahead vehicle travel
6 Hydraulic system
6.1 Gear pump for functions DT10
6.2 Gear pump for work operation DT10 with hydraulic PTO shaft (option)
6.3 Hydraulic distributor DT10 with tip skip, front tip skip (optional), self-loading equipment (optional), swivel tip skip (optional )
6.4 Hydraulic distributor DT10 with fold-up skip (option)
6.5 Hydraulic control valve DT10 with hydraulic PTO shaft (option)
6.6 Preference valve DT10 with hydraulic PTO shaft (option)
6.7 Test instructions
Checking the operating pressure of the operating hydraulics DT10 with skip, loader unit (option)
Checking the operating pressure of the hydraulic PTO shaft (option)
6.8 Hydraulics diagram DT10 with skip and loader unit (option)
6.9 Legend: hydraulics diagram DT10 with skip and loader unit (option)
6.10 Hydraulics diagram DT10 with skip, loader unit (option) and hydraulic PTO shaft (option)
6.11 Legend: hydraulics diagram DT10 with skip, loader unit (option) and hydraulic PTO shaft (option)
6.12 Hydraulics diagram DT10 with high-tip skip (option) and loader unit (option)
6.13 Legend: hydraulics diagram DT10 with skip and loader unit (option)
6.14 Hydraulics plan DT10 with rotary tip skip (optional)
6.15 Hydraulics plan DT10 with rotary tip skip (optional)
7 Electrical system
7.1 Ohm’s law (current, voltage, resistance); power
7.2 Measuring equipment, measuring methods
7.3 Electric units
7.4 Fuses
7.5 DT10 diagram
7.6 DT10 diagram (legend)
7.7 Engine wiring harness DT10
7.8 Instrument panel wiring harness DT10
7.9 Table of conductors DT10