Case CX160C Crawler Excavator Service Parts Catalogue (540419163PC) (September 2025)

That CX160C usually lives in mud, demo rubble, or tight utility digs, working all day swinging pipe, loading trucks, or trimming slopes. This Service Parts Catalogue is about planning the job before you crack a single fitting—so you trace what you’re going to touch, line up seals, pins, hoses, and clips, and don’t get caught waiting on a tiny O‑ring. Picture this: you’re about to pull a final drive that’s seeping; with this book, you can inspect the exploded view, match every gasket and bearing, and have it all on the bench before you lift the first bolt.

Applications & Use Cases

• Lay out a full undercarriage refresh by tracing the exploded track frame, then ordering the right rollers, idlers, and hardware in one shot.
• Isolate a leaking boom cylinder, check the rod and head drawings, and verify every seal and bushing so you only bleed the system once.
• During teardown, match part numbers off the diagram to what’s in your hand, so you don’t route in the wrong bushing because it “looks close enough.”
• Plan electrical work by following harness diagrams, then test and replace the exact connectors and clamps instead of guessing from a parts website photo.
• Keep a shelf stock list for common wear items—filters, pins, guards—by inspecting each section and building your own “shop minimums.”

FAQ

Q: Is this something I can search on a laptop, or just a bunch of scanned pages?

A: It’s typically set up so you can search part numbers and descriptions, then zoom in on diagrams, which makes matching parts during teardown a lot easier.

Q: Can I print pages to take out to the machine?

A: Yes, most folks print the sections they’re working on, stick them in a sleeve, and mark notes as they test, strip, and reassemble.

Safety Note

Always de-energize and support the machine properly before you start chasing parts, so you’re not inspecting or aligning components under a suspended load.

Case CX160C Crawler Excavator Index:

00.000.00 PICTORIAL INDEX – MAIN SECTIONS
00.000.00 PICTORIAL INDEX – MAIN SECTIONS
00.200.10 DIA KITS
05.100.01 ISL LIST A
05.100.01 ISL LIST A
05.100.02 ISL LIST B
05.100.02 ISL LIST B
05.100.03 CAPACITIES
05.100.04 [01] MAINTENANCE PARTS – FILTERS
10.001.AD [01] ENGINE
10.001.AD [01] ENGINE
10.001.AD [02] ENGINE
10.001.AD [03] ENGINE
10.001.AD [03] ENGINE
10.001.AD [03] ENGINE
10.001.AD [04] PACKAGE SEALS – ENGINE
10.001.AD [04] PACKAGE SEALS – ENGINE
10.001.AD [05] PACKAGE SEALS – ENGINE
10.001.AD [05] PACKAGE SEALS – ENGINE
10.001.AD [06] CYLINDER BLOCK
10.001.AD [06] CYLINDER BLOCK
10.001.AD [07] CYLINDER BLOCK
10.001.AD [07] CYLINDER BLOCK
10.001.AK ENGINE MOUNTING
10.001.AK ENGINE MOUNTING
10.004.10 FUEL FILLING PUMP – OPTIONAL
10.101.AA [01] CYLINDER HEAD
10.101.AA [01] CYLINDER HEAD
10.101.AA [02] CYLINDER HEAD
10.101.AA [02] CYLINDER HEAD
10.101.AB CYLINDER HEAD COVER
10.101.AB CYLINDER HEAD COVER
10.102.AP OIL PAN AND GAUGE
10.102.AP OIL PAN AND GAUGE
10.102.BB [01] FLYWHEEL HOUSING
10.102.BB [01] TIMING GEAR CASE AND FLYWHEEL HOUSING
10.102.BB [02] FLYWHEEL HOUSING
10.102.BB [02] TIMING GEAR CASE AND FLYWHEEL HOUSING
10.103.AD CRANKSHAFT PISTON AND FLYWHEEL
10.103.AD FLYWHEEL
10.106.AG [01] CAMSHAFT
10.106.AG [01] CAMSHAFT
10.106.AG [02] CAMSHAFT
10.106.AG [02] CAMSHAFT
10.202.AB AIR CLEANER WITH ELEMENT
10.202.AB AIR CLEANER WITH ELEMENT
10.206.AG FUEL FILTER
10.206.AG FUEL FILTER
10.210.10 FUEL FILLING PUMP – OPTIONAL

10.216.30 FUEL TANK PLUGS
10.216.AI FUEL TANK
10.216.AI FUEL TANK
10.216.AI [34] FUEL TANK PLUGS
10.216.BA [01] FUEL LINE
10.216.BA [01] FUEL LINE
10.216.BA [02] FUEL LINE
10.216.BA [02] FUEL LINE
10.218.AD FUEL FILLING PUMP – OPTIONAL
10.218.AD [01] FUEL FILLING PUMP – OPTIONAL
10.218.AD [02] FUEL FILLING PUMP – OPTIONAL
10.218.AE [01] FUEL INJECTION SYSTEM
10.218.AE [01] FUEL INJECTION SYSTEM
10.218.AE [02] FUEL INJECTION SYSTEM
10.250.AC [01] TURBOCHARGER SYSTEM
10.250.AC [01] TURBOCHARGER SYSTEM
10.250.AC [02] TURBOCHARGER SYSTEM
10.250.AC [02] TURBOCHARGER SYSTEM
10.250.AD [01] OIL AND VACUUM PIPING
10.250.AD [01] OIL AND VACUUM PIPING
10.250.AD [02] OIL AND VACUUM PIPING
10.250.AD [02] OIL AND VACUUM PIPING
10.250.AD [03] OIL AND VACUUM PIPING
10.250.AD [03] OIL AND VACUUM PIPING
10.254.99 EXHAUST SYSTEM
10.254.99 EXHAUST SYSTEM
10.254.AD [01] EXHAUST PIPE
10.254.AD [01] EXHAUST PIPE
10.254.AD [02] EXHAUST PIPE
10.254.AI MUFFLER – STANDARD
10.254.AI MUFFLER, STANDARD
10.254.AM INLET MANIFOLD
10.254.AM INLET MANIFOLD
10.304.AC OIL PUMP AND OIL STRAINER
10.304.AC OIL PUMP AND OIL STRAINER
10.304.AE OIL COOLER & FILTER
10.304.AE OIL COOLER & FILTER
10.400.AE WATER PIPING ENGINE
10.400.AE WATER PIPING ENGINE
10.400.BB RESISTOR
10.400.BB WATER PUMP AND CORROSION RESISTOR
10.400.BC THERMOSTAT & HOUSING
10.400.BC THERMOSTAT & HOUSING
10.400.BE RADIATOR – STANDARD
10.400.BE RADIATOR – STANDARD
10.400.BF RADIATOR – COMPONENTS
10.400.BF RADIATOR – COMPONENTS
10.414.AC FAN GUARD
10.414.AC FAN GUARD
TABLE OF CONTENTS
10.414.BE FAN AND BELT
10.414.BE FAN AND BELT
10.501.AA EMISSION PIPING
10.501.AA [01] EMISSION PIPING
10.501.AA [02] EMISSION PIPING
35.105.AC SUCTION LINE
35.105.AC SUCTION LINE
35.106.22 HYDRAULIC PUMP – OPTIONAL
35.106.AD [01] HYDRAULIC PUMP – STANDARD
35.106.AD [02] HYDRAULIC PUMP – COMPONENTS
35.106.AD [03] HYDRAULIC PUMP – COMPONENTS
35.106.AD [03] HYDRAULIC PUMP – COMPONENTS
35.106.AD [04] HYDRAULIC PUMP – COMPONENTS
35.106.AD [04] HYDRAULIC PUMP – COMPONENTS
35.106.AD [05] HYDRAULIC PUMP – COMPONENTS
35.106.AD [05] HYDRAULIC PUMP – COMPONENTS
35.106.AD [06] HYDRAULIC PUMP – COMPONENTS
35.106.AD [06] HYDRAULIC PUMP – COMPONENTS
35.106.AD [07] HYDRAULIC PUMP – SECOND OPTION
35.106.AD [07] OPTION
35.106.AD [08] HYDRAULIC PUMP – SECOND OPTION
35.106.AD [08] OPTION
35.106.AD [09] HYDRAULIC PUMP – SECOND OPTION
35.106.AD [09] OPTION
35.106.AD [10] HYDRAULIC PUMP – SECOND OPTION
35.106.AD [10] OPTION
35.106.AD [11] HYDRAULIC PUMP – SECOND OPTION
35.106.AD [11] OPTION
35.106.AD [12] HYDRAULIC PUMP – OPTIONAL
35.106.AD [12] HYDRAULIC PUMP – OPTIONAL
35.106.AO HYDRAULIC PUMP, RETURN LINE
35.106.AP PRESSURE LINE
35.106.AP PRESSURE LINE
35.106.AQ PILOT VALVE, SOLENOID, COMPONENTS
35.204.BE REMOTE CONTROL VALVE
35.204.BE REMOTE CONTROL VALVE
35.204.BE REMOTE CONTROL VALVE
35.204.BE REMOTE CONTROL VALVE
35.300.20 HYDRAULIC RESERVOIR
35.300.AQ HYDRAULIC FLUID RESERVOIR
35.300.AQ HYDRAULIC FLUID RESERVOIR
35.300.BC RETURN AND OIL COOLER LINE
35.300.BC RETURN AND OIL COOLER LINE
35.310.80 HYD. LINE – UNDERCARRIAGE
35.310.81 HYD. LINE – SUCTION LINE
35.310.82 HYD. LINE – SWING MOTOR
35.310.83 HYD. LINE – DRAIN LINE
35.310.AG DRAIN LINE
35.350.93 HOLDING VALVE

35.350.94 HOLDING VALVE
35.352.AI SWING LINE
35.352.AL SWING MOTOR INSTALL
35.352.AL [01] SWING MOTOR – COMPONENTS
35.352.AL [02] SWING MOTOR – COMPONENTS
35.353.AD [01] TRACTION MOTOR – COMPONENTS
35.353.AD [02] TRACTION MOTOR – COMPONENTS
35.353.AD [03] TRACTION MOTOR – COMPONENTS
35.353.AD [04] TRACTION MOTOR – COMPONENTS
35.353.AD [05] TRAVEL MOTOR & REDUCTION GEAR
35.353.AE TRACTION MOTOR LINE
35.354.20 SWING JOINT
35.354.AA CENTER JOINT
35.354.AF TRACTION LINE
35.355.01 JOYSTICK CONTROL
35.355.06 COVER
35.355.30 COVER
35.355.AH HAND CONTROL VALVE
35.355.AH SOLENOID VALVE
35.356.AB FOOT CONTROL VALVE – OPTIONAL
35.357.AK [01] PILOT LINE – STANDARD
35.357.AK [02] PILOT LINE – STANDARD
35.357.AK [03] PILOT LINE – STANDARD
35.357.AK [04] PILOT LINE – STANDARD
35.357.AK [05] PILOT CONTROL LINE – HBCV
35.359.10 VALVE SHUT-OFF – OPTIONAL
35.359.30 REMOTE CONTROL VALVE
35.359.AB [01] CONTROL VALVE – OPTIONAL
35.359.AB [02] CONTROL VALVE – OPTIONAL
35.359.AB [03] CONTROL VALVE – OPTIONAL
35.359.AB [04] CONTROL VALVE – OPTIONAL
35.359.AB [05] CONTROL VALVE – OPTIONAL
35.359.AB [06] CONTROL VALVE – STANDARD
35.359.AB [07] DIRECTIONAL CONTROL VALVE – STANDARD
35.359.AB [08] DIRECTIONAL CONTROL VALVE – STANDARD
35.359.AB [09] DIRECTIONAL CONTROL VALVE – STANDARD
35.359.AB [10] DIRECTIONAL CONTROL VALVE – STANDARD
35.359.AN [01] HOLDING VALVE
35.359.AN [02] HOLDING VALVE
35.630.AK [01] SHUT-OFF VALVE
35.630.AK [02] STOP VALVE
35.630.AK [03] STOP VALVE
35.630.AK [04] STOP VALVE
35.736.AA [01] BOOM CYLINDER – LH
35.736.AA [02] BOOM CYLINDER – RH
35.736.AA [03] BOOM CYLINDER HBCV – LH
35.736.AA [04] BOOM CYLINDER HBCV – RH
35.736.AC [01] BOOM CYLINDER LINES
35.736.AC [02] BOOM CYLINDER LINES
TABLE OF CONTENTS
35.736.AC [03] SECOND OPTION LINE – STANDARD 2.62 M
35.736.AC [04] BOOM LINE
35.736.AC [05] SECOND OPTION LINE – LONG 3.05 M
35.736.AC [06] BOOM CYLINDER LINES
35.736.AC [07] OPTION LINE – BOOM
35.736.AC [08] OPTION LINE – LONG
35.736.AC [09] OPTION LINE – LONG
35.736.AC [10] HYDRAULIC LINES BUCKET & ARM
35.737.AA [01] DIPPER CYLINDER
35.737.AA [02] DIPPER CYLINDER
35.737.AE [01] DIPPER CYLINDER LINES
35.737.AE [02] DIPPER CYLINDER LINES
35.737.AE [03] DIPPER CYLINDER LINES – OPTION
35.738.AA BUCKET CYLINDER
35.738.AE [01] BUCKET CYLINDER LINES
35.738.AE [02] BUCKET CYLINDER LINES – LONG ARM
35.900.10 HYD. LINE – DIPPER CYLINDER
35.900.11 HYD. LINE – DIPPER CYLINDER – OPTIONAL
35.900.12 HYD. LINE – DIPPER – OPTIONAL
35.900.20 HYD. LINE – BOOM CYLINDER
35.900.21 HYD. LINE – BOOM – OPTIONAL
35.900.22 [01] HYD. LINE – BOOM CYLINDER – OPTIONAL
35.900.22 [02] HYD. LINE – BOOM CYLINDER – OPTIONAL
35.900.30 HYD. LINE – BUCKET CYLINDER
35.900.31 HYD. LINE – BUCKET CYLINDER – LONG DIPPER
35.964.10 DIPPER CYLINDER
35.964.11 DIPPER CYLINDER
35.964.20 BOOM CYLINDER – RIGHT
35.964.21 BOOM CYLINDER – LEFT
35.964.22 BOOM CYLINDER – RIGHT
35.964.23 BOOM CYLINDER – LEFT
35.964.30 BUCKET CYLINDER
37.140.20 COUNTERWEIGHT – SOUNDPROOFING
39.100.AB LOWER FRAME
39.101.40 SWING COMPONENTS
39.101.AC UPPER FRAME
39.102.20 UNDERCARRIAGE
39.103.99 SLEWING RING
39.140.AM COUNTERWEIGHT, 3400 KG
48.100.20 TRACK – FOOTSTEP – 600 MM
48.100.30 TRACK – FOOTSTEP – 700 MM
48.100.AD [01] GROUSER SHOE – 600 MM SEAL
48.100.AD [02] GROUSER SHOE – 700 MM SEAL
48.110.AA RECOIL SPRING
48.130.AC LOWER UNDER COVER
48.130.AO [01] GUIDE PULLEY
48.130.AO [02] GUIDE CHAIN – SINGLE
48.130.AO [03] GUIDE CHAIN – TRIPLE
48.138.10 ROLLER UPPER

90.108.AA [01] DECAL, CAB
90.108.AA [02] DECAL, CAB
90.108.AA [02] DECAL, CAB (ANZ)
90.108.AA [03] DECAL, CAB
90.108.AA [04] DECALS – HAND CONTROL
90.108.AA [05] DECALS – HAND CONTROL
90.108.AA [06] DECALS – HAND CONTROL
90.108.AB DECALS – EXTERNAL
90.108.AF DECALS – NAMEPLATE, ISO
90.110.10 OPERATORS COMPARTMENT – MAT, FLOOR – STANDARD
90.110.50 OPERATORS COMPARTMENT – CAB ACCESSORIES
90.110.AV [01] CONSOLE, SIDE PANEL, RIGHT
90.110.AV [01A] CONSOLE, SIDE PANEL, RIGHT
90.110.AV [01B] CONSOLE, SIDE PANEL, RIGHT
90.110.AV [02] CONSOLE, SIDE PANEL, LEFT
90.110.AV [02A] CONSOLE, SIDE PANEL, LEFT
90.110.AV [02B] CONSOLE, SIDE PANEL, LEFT
90.110.BD FLOOR MAT – STANDARD
90.114.BE CAB GUARD – FOPS – LEVEL 2
90.116.BE UPPER UNDER COVER
90.118.BM REAR VIEW MIRROR
90.119.10 CAB GUARD – FRONT
90.119.70 CAB VANDAL GUARD
90.119.71 CAB VANDAL GUARD
90.119.AB [01] CAB GUARD – VANDAL
90.119.AB [02] CAB GUARD – VANDAL
90.120.AE [01] SEAT, MECHANICAL SUSPENSION, CUSHION
90.120.AJ [01] SEAT, MECHANICAL SUSPENSION, SUPPORT
90.120.BB [01] DOG CHAIN
90.120.BB [02] SEAT, MECHANICAL SUSPENSION
90.124.AE [01] SEAT, AIR SUSPENSION
90.124.AE [01A] SEAT, AIR SUSPENSION
90.124.AH [01] SEAT, AIR SUSPENSION, CUSHION
90.124.AN [01] SEAT, AIR SUSPENSION, SUPPORT
90.124.AN [01A] SEAT, AIR SUSPENSION, SUPPORT
90.150.20 CAB – VISOR
90.150.21 CAB – VISOR
90.150.30 CAB GUARD – WINDSHIELD, LOWER
90.150.31 CAB GUARD – WINDSHIELD, UPPER
90.150.32 CAB GUARD – WINDSHIELD, UPPER AND LOWER
90.150.33 CAB GUARD
90.150.40 CAB – RADIO PRE-EQUIPMENT
90.150.50 CAB – GLASS – INSTRUMENT PANEL
90.150.AB [01] CAB ASSY
90.150.AB [02] CAB ASSY
90.150.AB [03] CAB ASSY
90.150.AB [04] CAB ASSY
90.150.AB [05] CAB ASSY
90.150.AB [06] CAB ASSY
TABLE OF CONTENTS
90.150.BJ [01] CAB FRONT GUARD – MESH, LOWER WINDSHIELD
90.150.BJ [02] CAB FRONT GUARD – MESH, UPPER WINDSHIELD
90.150.BJ [03] CAB FRONT GUARD – MESH, UPPER AND LOWER WINDSHIELD
90.151.AE [01] RAIN REFLECTOR
90.151.AE [02] RAIN REFLECTOR
90.151.AE [03] CAB – SUN VISOR
95.100.010 [01] HAMMER – CH-100
95.100.020 [01] ATTACHMENT, COMPACTOR – SC80
95.100.030 [01] HYDRAULIC QUICK COUPLER COMPLETING KIT CE-ATT
95.100.030 [02] HYDRAULIC QUICK COUPLER COMPLETING KIT CE-ATT
95.100.030 [03] HYDRAULIC QUICK COUPLER COMPLETING KIT CE-ATT
95.100.030 [04] HYDRAULIC QUICK COUPLER MULTI-FIT S KIT CE-ATT
95.100.030 [05] HYDRAULIC QUICK COUPLER MULTI-FIT S KIT CE-ATT
95.100.040 [01] THUMB
95.100.050 [01] BUCKET W/ SIDE CUTTER – HD & XHD
95.100.050 [03] BUCKET, SCOOP
95.100.050 [04] DITCH CLEANING BUCKET
95.100.060 [01] RIPPER
95.100.070 [01] WINDSHIELD, GUARD, MESH – NA ONLY
95.100.070 [02] WINDSHIELD, GUARD, LEXAN – NA ONLY

CNH