CNH FRONT AND ARTICULATION CHASSIS GUARDS KIT Installation Instructions (91867892)

These guards are for machines that live in the rough stuff—rock piles, demolition rubble, forestry slash, muddy sites where you’re always climbing over something sharp. This manual walks you through how to install the front and articulation chassis guards so they actually protect the belly and joints instead of rattling loose or rubbing hoses. Say you keep tearing up steering lines on stumps; with this, you can trace the mounting points, route everything clean, and verify the guards clear when the frame articulates.

Applications & Use Cases

• Plan the install so you can line up hardware, support the machine safely, and inspect the frame before you start bolting guards on.
• Isolate interference points by cycling the articulation and checking where guards might hit hoses, wiring, or tires before you fully tighten anything.
• Align and test-fit each guard section, then snug it down in sequence so you don’t twist the frame brackets or crack welds.
• Trace and route hydraulic lines, harnesses, and grease lines around the new guards, then verify nothing’s pinched or rubbing at full lock.
• Re-check and inspect fasteners after a few hours of work, so you can catch loosening or flexing early instead of losing a panel in the mud.

FAQ

Q: Is this a PDF I can search on my laptop or phone?

A: It’s typically a standard PDF, so you can keyword search for steps, torque notes, and diagrams.

Q: Can I print just the pages I need to take to the jobsite?

A: Yeah, you can usually print selected pages, stick them in a sleeve, and keep greasy hands off your phone.

Safety Note

Always support the machine properly and never work under the chassis or articulation area with only the hydraulic system holding it up.

CNH FRONT AND ARTICULATION CHASSIS GUARDS KIT Index:

1 SAFETY INFORMATION
Basic instructions – Important notice regarding equipment servicing. . . . . . . . . . . . . . . . . . . . . . . 1-1
Advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Safety rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
2 KIT CONTENT
Kit overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
3 GENERAL INFORMATION
Basic instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
4 PRE-ASSEMBLY
PREPARING FOR ASSEMBLY
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
5 ASSEMBLY
Install
Front articulation joint guards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

CNH

91823141 – FRONT AND ARTICULATION CHASSIS GUARDS KIT
CASE CONSTRUCTION
651G Wheel loader StageV STD – High
Performance
651G Wheel loader StageV STD – High
Performance
651G Wheel loader StageV STD – High
Performance
651G Wheel loader StageV STD – High
Performance
651G Wheel loader, Tier 4B (final), standard
linkage – High Performance
651G Wheel loader, Tier 4B (final), standard
linkage – High Performance
651G Tier 4B (final) – ZB linkage – 2025
Updates
651G Tier 4B (final) – ZB linkage – 2025
Updates
651G Tier 4B (final) – XT linkage – 2025
Updates
651G Tier 4B (final) – XT linkage – 2025
Updates
651G Tier 4B (final) – XR linkage – 2025
Updates
651G Tier 4B (final) – XR linkage – 2025
Updates
651G+ Stage V STD – Cab Upgrade
651G+ Stage V STD – Cab Upgrade
651G+ Stage V STD – Cab Upgrade
651G+ Stage V STD – Cab Upgrade
Lec