Case 580SV, 695SV Tier 4B Final Tractor Loader Backhoe Operators Manual (92740621) (September 2025)
These 580SV / 695SV backhoes usually live in the rough stuff—sites with ruts, piles, mud, and tight spots around utilities. This operators manual helps you run the machine right day to day: how the controls actually respond when you’re digging, loading trucks, backing up a slope, or working in soft ground. Say you’re trenching near a buried line; the book walks you through how to set up, stabilize, trace your movements, and avoid sudden swings that can bite you or the pipe.
Applications & Use Cases
- Trace and learn the controls so you know how the boom, dipper, and loader react under load, on a side slope, or when the tires start to sink.
- Follow the daily walk‑around to check fluids, inspect hoses, verify tire condition, and catch leaks before they strand you.
- Use the procedures to safely bleed pressure, then disconnect or route hydraulic lines so you don’t pop a hose in your face.
- Isolate weird behavior—slow hydraulics, odd noises, steering pull—by running the basic tests they outline before you call a tech.
- Align your operating habits with what Case expects so you don’t fight the machine or abuse the transmission and brakes.
FAQ
Q: Is this a PDF I can search on my laptop or phone?
A: Yes, it’s typically a searchable PDF, so you can jump to sections by keyword instead of flipping pages.
Q: Can I print just a few pages to keep in the cab?
A: You usually can; most folks print the daily checks, control layout, and safety pages for jobsite use.
Safety Note
Always drop the attachments, kill the engine, and release hydraulic pressure before you inspect or crack any line loose.
Case 580SV, 695SV Tier 4B Final Tractor Loader Backhoe Index:
- GENERAL INFORMATION
- Note to the owner
- Intended use
- Electro-Magnetic Compatibility (EMC)
- Product identification
- Read the operator’s manual
- Operator’s manual storage on the machine
- Machine orientation
- Component Identification
- Selective Catalytic Reduction (SCR) exhaust treatment – Product overview
- Emissions overview
- SAFETY INFORMATION
- Safety rules and signal word definitions
- Safety rules
- Seat belt
- Fire extinguisher
- Safety rules – Utility precautions
- Safety rules – Fuel handling precautions
- Safety rules – Specific precautions to this machine
- Safety rules – Ductile iron
- Support strut for loader lift arm – Two-Wheel Steer (2WS)
- Support strut for loader lift arm – Four-Wheel Steer (4WS)
- Hand signals
- Ecology and the environment
- Noise and vibration levels
- Safety signs – Center-Pivot (CP)
- Safety signs – Side-Shift (SS)
- Selective Catalytic Reduction (SCR) decals
- CONTROLS AND INSTRUMENTS
- Access to operator’s platform
- Access to operator’s platform
- Cab windshield and windows – Open/Close
- Operator’s seat
- Forward controls
- Steering column
- Right-hand multi-functional lever
- Front control panel – Two-Wheel Steer (2WS only)
- Front control panel – Four-Wheel Steer (4WS only)
- Pedal controls
- Transmission controls
- Right-hand side controls
- Key start switch
- Parking brake switch
- Console controls
- Right side post controls
- Exterior controls
- Battery master switch
- Rotating beacon (Optional)
- INSTRUMENT CLUSTER
- Instrument Cluster (IC)
- Menu screen display
- Selective Catalytic Reduction (SCR) exhaust treatment – Overview
- NO TITLE
- NO TITLE
- NO TITLE
- NO TITLE
- CAB CONTROLS AND ADJUSTMENTS
- Cab features
- Bluetooth® radio (if equipped)
- LOADER ATTACHMENT CONTROLS
- Loader attachment control lever
- BACKHOE ATTACHMENT CONTROLS
- Remove the backhoe from the stowed position – center pivot
- Place the backhoe in the stowed position – center pivot
- Remove the backhoe from the stowed position – side shift
- Place the backhoe in the stowed position – side shift
- Backhoe attachment pilot controls version
- CLIMATE CONTROLS
- Heating, Ventilation, and Air Conditioning (HVAC) controls
- Cab air louvers
- OPERATING INSTRUCTIONS
- Commissioning the unit
- Before using the machine
- Operating the machine
- Run in period of a new machine
- Starting the unit
- Before starting the engine
- Normal engine starting
- Engine speed
- Cold temperature operation
- Hot temperature operation
- Operating the machine in high altitude
- Operating the machine in water
- Assisted starting (Jump-starting)
- Stopping the unit
- Moving the unit
- Job site travel
- Before operating the machine
- Traveling on a hill
- Auto powershift
- 2WD or 4WD
- Steer selection (4WS)
- Differential lock button
- Auto-Ride Control™ (ARC) – Four-Wheel Drive (4WD) only
- Parking the unit
- TRANSPORT OPERATIONS
- Road transport
- Precautions for road travel
- Preparing for road transport
- Preparing the machine for road travel
- Shipping transport
- Transporting on a trailer
- Lifting the machine
- Recovery transport
- WORKING OPERATIONS
- General information
- Forward-Neutral-Reverse (F-N-R) shift sensitivity
- Display brightness
- Maximum throttle/Cold start idle
- Throttle sensitivity
- Brake Enabled Idle (BEI)
- Auto idle time-out adjustment
- Auto engine shutdown time-out adjustment
- Auto engine protection shutdown setting
- Auto-Ride Control™ (ARC) speed thresholds
- Direct Drive enable/disable (if equipped)
- LOADER ATTACHMENT
- Personal safety
- Job layout
- Comfort Steer™ (if equipped)
- Transmission disconnect trigger
- Detent position for loader control auxiliary hydraulics
- ECO power mode
- Operating the loader attachment
- Loader digging force
- Loader bucket removal
- Loader bucket install
- Hydraulic coupler – changing attachments (if equipped)
- Loader bucket with forks (optional)
- BACKHOE ATTACHMENT
- Personal safety
- Basic instructions
- Backhoe danger area
- Swing lock
- Basic backhoe operations
- Setting the backhoe attachment in working position
- Stabilizer pads – center-pivot machines
- Stabilizer pads – side-shift machines
- Backhoe attachment – side-shift machines
- Hydraulic backhoe bucket quick coupler , if equipped (Overlapping cylinder boom models only)
- Auxiliary hydraulics
- Backhoe thumb lock (if equipped)
- Operating the backhoe attachment – center pivot
- Operating the backhoe attachment – side shift
- Power Lift™
- Power Boost
- Backhoe bucket – Removal
- Backhoe bucket – Installation
- Backhoe bucket – Digging angle
- Ballasting
- Lifting loads with backhoe attachment
- Backhoe thumb (if equipped)
- Auto idle operation
- One-Touch Idle (OTI), if equipped
- MAINTENANCE
- General information
- Maintenance safety
- Fire extinguisher
- Engine hood
- Fuel tank
- General specification – Diesel fuel
- General specification – Biodiesel fuels
- Selective Catalytic Reduction (SCR) exhaust treatment – Basic instructions
- Hydraulic oil
- Work hours and intervals
- Engine oils
- Organic Acid Technology (OAT) coolant
- Capacities – Two-Wheel Steer (2WS) machines
- Capacities – Four-Wheel Steer (4WS) machines
- Diagnostic/Service tool port
- Hydraulic diagnostic test ports
- Maintenance planning
- At warning message display
- Engine air filters
- Hydraulic filter(s)
- Fuel system water separator
- Diesel Exhaust Fluid (DEF)/AdBlue®/ARLA tank – Filling
- Diesel Exhaust Fluid (DEF)/AdBlue®/ARLA tank – Drain fluid
- Hydrocarbon management
- Initial 10 hours
- Every 10 hours
- Checks at start-up and before each workshift (10 hours)
- Working attachments — Loader attachment
- Working attachments — Backhoe attachment
- Engine oil level — Check
- Engine coolant — Check
- Radiator, oil cooler, and condenser — Check
- Alternator — Check
- Hydraulic oil level — Check
- Hydraulic hoses, tubes, and fittings
- Check wheels and tires
- Every 50 hours
- Working attachments – greasing
- Backhoe thumb (if equipped) – greasing
- Door hinges
- Front axle trunnion
- Front axle king pins
- Seat and seat belt
- Fuel pre-filter – draining condensation
- Tire pressure
- Every 250 hours
- Drive shaft lubrication
- Engine cooling system — Check
- Fuel tank – Drain fluid
- Hydraulic oil tank breather / filler cap – cleaning
- Transmission oil level
- Front axle breather (4WD) – Clean
- Front axle and reduction gear oil level (4WD)
- Front axle system – Check — (2WD)
- Rear axle and reduction gear oil level
- Rear axle breather
- Radiator and condenser – cleaning
- Drive belts – check
- Cab air filter
- Heater and evaporator (Air-conditioning system) – Cleaning
- Telescopic dipper
- Battery terminals
- Roll Over Protective Structure (ROPS) mechanism and hardware check
- Every 500 hours
- Engine oil and filter
- Fuel filter
- Fuel prefilter
- Diesel Exhaust Fluid (DEF)/AdBlue® tank filler screen
- Diesel Exhaust Fluid (DEF)/AdBlue® in-line filter
- Extendahoe® wear pad – adjustment and greasing
- Every 1000 hours
- Hydraulic oil filter
- Hydraulic oil
- Power shuttle transmission – Oil change
- Power shuttle transmission – Oil filter replacement
- Power shuttle transmission – Screen filter cleaning
- Powershift transmission – Oil change
- Powershift transmission – Oil filter replacement
- Front axle fluid – Four-Wheel Drive (4WD)
- Rear axle
- Machine inspection and cleaning
- Brake pedal lever – Greasing
- Hydraulic cylinders
- Alternator – check
- Every 1500 hours of operation or annually
- Every 3000 hours
- Diesel Exhaust Fluid (DEF)/AdBlue® supply module filter
- Every 4000 hours
- As required
- Drive belt
- Air-conditioning compressor drive belt
- Turbocharger – Check
- Fuel system bleeding
- Battery removal and installation
- Telescopic dipper (if equipped)
- Bucket teeth
- Loader bucket – Self-leveling adjustment
- Disable parking brake
- Hydraulic system – Release pressure
- Bi-directional auxiliary hydraulic pressure and flow
- Uni-directional auxiliary hydraulic pressure and flow
- Machine lights
- Fuses and relays – Power shuttle
- Fuses and relays – Powershift
- Stabilizers (side-shift) – Clearance check and adjustment
- Storage
- Machine storage
- Preparation for use after storage
- TROUBLESHOOTING
- Fault code resolution
- Troubleshooting
- Engine – Troubleshooting
- Starter motor – Troubleshooting
- Alternator – Troubleshooting
- Transmission – Troubleshooting
- Axles – Troubleshooting
- Steering system – Troubleshooting
- Hydraulic systems – Troubleshooting
- Loader attachment – Troubleshooting
- Backhoe attachment – Troubleshooting
- Swing – Troubleshooting
- Hydraulic pump – Troubleshooting
- Electrical systems – Troubleshooting
- Cab – Troubleshooting
- Air-conditioning system – Troubleshooting
- Alarm(s)
- SPECIFICATIONS
- Capacities – Two-Wheel Steer (2WS) machines
- Capacities – Four-Wheel Steer (4WS) machines
- Engine
- Powertrain
- Brakes and controls
- Hydraulics
- Front counterweight
- Buckets
- Tires
- Dimension – Two-Wheel Steer (2WS), Tool Carrier (TC), Center-Pivot (CP)
- Dimension – Two-Wheel Steer (2WS), Tool Carrier (TC), Side-Shift (SS)
- Dimension – Four-Wheel Steer (4WS), Tool Carrier (TC), Side-Shift (SS)
- Dimension – Four-Wheel Steer (4WS),Tool Carrier (TC), Center-Pivot (CP)
- Loader performances – Loader Arm
- Dimension – Two-Wheel Steer (2WS) w/ 14FT Backhoe
- Dimension – Two-Wheel Steer (2WS) w/ 15FT Backhoe
- Dimension – Four-Wheel Steer (4WS) w/ 15FT Backhoe
- Backhoe hydraulic lifting capacities – Two-Wheel Steer (2WS) w/ 14FT Backhoe
- Backhoe hydraulic lifting capacities – Two-Wheel Steer (2WS) w/ 15FT Backhoe
- Backhoe hydraulic lifting capacities – Four-Wheel Steer (4WS) w/ 15FT Backhoe
- ACCESSORIES
- Mechanical loader bucket quick coupler
- Mechanical backhoe bucket quick coupler
- Backhoe attachment auxiliary hydraulic tools
- Backhoe attachment safety valves
- Reversible stabilizer pads
- Universal backhoe bucket coupler
- Telematics with Case SiteWatch™
CNH
