CNH TRIMBLE EARTHWORKS MECHANICAL KIT Installation Instructions (92649334)

Out on a grading site, this kit’s going on a dozer, grader, or excavator that spends its life in dust, vibration, rain, and the occasional rock strike. This installation manual walks you through how to mount, route, and align the CNH Trimble Earthworks mechanical kit so the machine control actually reads the ground right. Say your blade keeps cutting high on one side—this is the kind of guide you use to trace the sensor mounts, verify the brackets, and re-check the geometry instead of just guessing.

Applications & Use Cases

• Route harnesses and mount sensors so they don’t rub, pinch, or hang where they’ll get ripped off during normal digging or pushing.
• Isolate bad readings by checking bracket orientation, testing sensor movement, and inspecting linkage points the manual calls out.
• Align masts, receivers, and reference points so the system usually calibrates cleanly without fighting you all afternoon.
• Verify you’ve used the right fasteners and installed them in the proper order, so nothing loosens once the machine starts working hard.
• Trace post-install faults by comparing your setup to the manual’s step sequence instead of tearing everything back off.

FAQ

Q: Is this a PDF I can search on a laptop or tablet?

A: It’s typically a searchable PDF, so you can jump to sections and use find for part names or steps.

Q: Can I print just the pages I need for the jobsite?

A: Yes, most folks print the wiring and mounting pages, stick them in a sleeve, and keep the full file on a tablet in the truck.

Safety Note

Always power down, secure the implement, and verify all raised components are supported before you route wiring or work around the linkage.

CNH TRIMBLE EARTHWORKS MECHANICAL KIT Index:

SAFETY INFORMATION
Basic instructions – Important notice regarding equipment servicing. . . . . . . . . . . . . . . . . . . . . . . 1-1
Safety rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
2 KIT CONTENT
Kit overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
3 GENERAL INFORMATION
Basic instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
4 PRE-ASSEMBLY
PREPARING FOR ASSEMBLY
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
5 ASSEMBLY
Install
Trimble ready kit installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
6 POST-ASSEMBLY
INSTRUCTIONS
Post-assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

CNH

92649335 – TRIMBLE EARTHWORKS MECHANICAL KIT
CASE CONSTRUCTION
836D Mechanical Controls, Stage V – ZF
EC4 Transmission Control Unit
836D AWD Mechanical Controls, Stage
V – ZF EC4 Transmission Control Unit
[FNH836DANZHF01807 – ]