Develon HX1000A L Crawler Excavator Operation and Maintenance Manual (950106-03350A-EN)
Out on big earthmoving jobs, quarries, or pipe runs, this HX1000A’s working hard in dust, mud, and long shifts. This operation and maintenance manual helps you set a steady service rhythm so you can trace problems early, not when the trench is open and trucks are waiting. Say the boom starts moving a bit jerky on a busy morning—this book walks you through what to check first, what to inspect next, and when it’s time to call in a tech instead of guessing.
Applications & Use Cases
- Set up daily walk‑around checks so you can spot leaks, loose hardware, and track issues before they turn into downtime.
- Plan weekly and seasonal services—grease points, filter changes, coolant checks—so the machine stays predictable during peak work.
- Use the procedures to isolate odd noises or warning lights, then verify your fix instead of just clearing alarms and hoping.
- Follow the steps to bleed fuel or hydraulic lines properly after a repair, so you don’t fight air in the system all day.
- Route and align wear parts and hoses the way the factory intended, which usually stops repeat failures in the same spots.
FAQ
Q: Is this manual searchable, or am I scrolling forever on a phone?
A: It’s typically a searchable PDF, so you can jump to sections by keyword; a tablet or laptop works best on site.
Q: Can I print just the service parts I need for the shop?
A: Yes, you can usually print specific sections, which is handy for greasy hands at the bench while keeping the main file clean.
Safety Note
Always relieve hydraulic pressure and verify all lockout steps before you inspect, loosen, or remove any line or component.
Develon HX1000A L Crawler Excavator Index:
- HX1000A L
- Table of Contents
- Foreword
- Intended Use
- Engine and Emission Control System Maintenance
- Machine Capacity
- Attachments
- Product Identification Number (PIN)
- Component Serial Numbers
- Engine Identification
- Machine Serial Numbers
- Safety Messages
- EC Declaration of Conformity (Original instruction)
- Safety
- Safety Decals
- Safety Decals – Information and Location
- General
- Operator’s Responsibility – Safe Operation
- Know Your Machine
- Proper Work Tools and Attachments
- Pressurized Fluids
- Flying or Falling Objects
- Personal Protective Equipment (PPE)
- Correction of Machine Problems
- Crushing and Cutting
- Hot Coolant and Oils – Burn Prevention
- Fire and Explosion Prevention
- Fire Extinguisher and First-aid Kit (Emergency Medical Kit)
- Electrical System and Electrical Shock
- Roll-over Protective Structure (ROPS)
- Regulation 8.35(2) of the Mines Safety and Inspection Regulations (1995)
- Transportation
- Obey State and Local Over-the-Road Regulations
- Loading and Unloading
- Transporting Machine
- Operation
- Before Engine Starting
- Work Site
- Mounting/Dismounting
- Cleaning
- Operator Station
- Seat Belt
- Visibility Information
- Boost Starting or Charging Engine Batteries
- Starting Engine
- Swinging or Traveling
- Lifting and Digging
- Operation on Slopes
- Towing
- Attachment
- Equipment Lowering with Engine Stopped
- Engine Stop
- Parking Machine
- Long Term Storage
- Before Storage
- During Storage
- After Storage
- Maintenance
- Warning Tag
- Cleaning
- Proper Tools and Clothing
- Disassembling Precautions
- Use of Lighting
- Fire and Explosion Prevention
- Burn Prevention
- Rubber That Contains Fluorides
- Rubber and Plastics
- Welding Repairs
- Warning for Counterweight and Front Attachment Removal
- Lock Inspection Covers
- Working on Machine
- Accumulator
- Compressed Air
- Track Tension Adjustments
- Supports and Blocking for Work Equipment
- High-pressure Lines, Tubes and Hoses
- Battery
- Environment and Circumstances
- Work Site Areas Requiring Extra Caution
- High-voltage Cables
- Underground Operation
- Working in Water
- Working in Contaminated Environment
- Operation in Extreme Conditions
- Exhaust Ventilation
- Asbestos Information
- Silica Dust Information
- Disposal of Hazardous Materials
- Sound
- Vibration Information
- Operating Controls
- Component Locations
- Operator’s Area
- Operational Controls and Panels
- 1. Starter Switch
- 1-1. Start/Stop Button
- 2. Smart Key
- 3. Air Conditioning and Heating Control Panel
- 4. 12V Power Socket
- 5. 24V Power Socket
- 6. USB Charger
- 7. Bluetooth Control Panel
- 8. Wiper Control Panel
- 9. Engine Speed Control Dial
- 10. After Treatment System Switch
- 11. Light Switch
- 12. Travel Speed Selector Switch
- 13. Lower Wiper Switch (If Equipped)
- 14. Overload Warning Switch (If Equipped)
- 15. Buzzer Alarm Stop Switch (If Equipped)
- 16. Swing Priority Switch
- 17. Cabin Work Light Switch (If Equipped)
- 18. Intelligent Floating Boom Switch (If Equipped)
- 19. Warning Light Switch (If Equipped)
- 20. Reverse Fan Switch
- 21. Air Compressor Switch (If Equipped)
- 22. Auto Grease System Switch (If Equipped)
- 23. Emergency Start Mode Switch
- 24. Auxiliary Mode Switch
- 25. Quick Coupler Switch (If Equipped)
- 26. Swing Brake Release Switch
- 27. Photo Sensor
- 28. Display Monitor
- 29. Around View Monitoring (AVM) Monitor (If Equipped)
- 30. Hour Meter
- 31. Micro Phone (If Equipped)
- 32. Safety Lever
- 33. Horn Button
- 34. Breaker/Booster Button
- 35. Rotating Button (If Equipped)
- 36. Shear Button (If Equipped)
- Display Monitor
- Functional Check
- Setting a Password
- 1. Fuel Gauge
- 2. DEF (AdBlue®) Level Gauge
- 3. Engine Coolant Temperature Gauge
- 4. Hydraulic Oil Temperature Gauge
- 5. Tachometer
- 6. Audio Display
- 7. Main Warning Lamp
- 8. Digital Clock
- 9. Favorites Button
- 10. Main Information Selector Button
- 11. Main Information Indicator
- 12. Power Mode Selector Button
- 13. Power Mode Indicator
- 14. Operating Mode/Flow Setting Selector Button
- 15. Auto Idle Selector Button
- 16. Menu Selector Button
- 17. Back Button
- 18. Camera Mode Selector / ESC Button
- 19. Jog Switch
- 20. Mode Symbol Display
- 21. Indicator Display
- 22. Display Warning Symbols
- Warning Pop-Up Messages
- User Menu
- User Menu – Access and Escape Methods
- Around View Monitoring (AVM) System (If equipped)
- Operating Conditions and Instructions
- Screen Components and View Modes
- Displaying Outlines of the Vehicle Area
- Proximity Alarm System (If Equipped)
- Sensor Locations
- Sensor Operating Conditions and Settings
- Sensor Alarm Setting
- Operating Range and Display
- Heater and Air Conditioner Control Panel
- Location of Controls and Vents
- Control Panel
- Memory Function
- Additional Operating Instructions
- Miscellaneous Electrical Devices
- Cabin Light
- Safety Lever
- Circuit Breaker (50A, 80A)
- Junction Box
- DAB (Digital Audio Broadcasting) Audio
- Seat Adjustment
- 1. Forward/Backward Adjustment
- 2. Adjusting Height of Seat and Depth of Cushion
- 3. Reclining Position Adjustment
- 4. Headrest
- 5. Lumbar Support Adjustment
- 6. Seat Heater Switch
- 6-1. Heating/Ventilation Switch (If Equipped)
- 7. Left and Right Control Stand Adjustment
- 8. Left and Right Control Stand Height Adjustment
- 9. Adjusting Height/Angle of Armrest
- Seat Belt
- Seat Belt Locking and Unlocking
- Engine Emergency Stop Switch
- Emergency Exit Glass Breaking Tool
- Miscellaneous Convenience Devices
- Ceiling Cover
- Front Windows
- Door Side Latch
- Cabin Storage Compartments
- Sun Visor
- Sunglasses Case
- Cup Holder
- Storage Box
- Miscellaneous Access Covers and Doors
- Side Door
- Storage Box Door
- Battery Room Door
- Engine Cover
- Air Gun and Compressor (If Equipped)
- Air Gun
- How to Use Air Compressor
- How to Connect Air Gun
- Operation
- To Operate a New Excavator
- Starting and Stopping Engine
- Inspection Before Starting Engine
- Operational Checks Before Starting Engine
- Engine Start
- Diesel Heater (If Equipped)
- Hydraulic System Warm-up
- Hydraulic System Warm-up – Cold Weather
- Stopping Engine
- Checks and Maintenance After Stopping Engine
- Wait to Disconnect Indicator
- DEF (AdBlue®) Level Lamp
- Safety Lever
- Travel
- Automatic Travel Speed Control
- Travel Control Lever Operation
- General Travel Instructions
- Straight Travel Pedal (If Equipped)
- Operating Instructions
- Engine Speed Control
- Emission Control System
- After Treatment System
- Delayed Engine Shutdown (DES)
- Mode Selection
- Change Machine Control Pattern By Selector Valve (If Equipped)
- Work Levers (Joysticks) (ISO Pattern)
- Work Levers (Joysticks) (BHL Pattern)
- Intelligent Floating Boom Control (If Equipped)
- Smart Power Control (SPC)
- Operating Precautions
- Working in Water
- Escaping From Mud
- Parking Excavator
- Towing Procedure
- Attachments
- Bucket – Replace and Reverse
- Breaker Operation
- Shear Operation
- One-Way/Two-Way Valve Operation
- Rotating Operation
- Quick Coupler Operation
- Lifting Objects
- Lifting Objects with Quick Coupler
- Operation Under Abnormal Conditions
- Equipment Lowering with Engine Stopped
- Removable Counterweight (If Equipped)
- Auto Grease System (If Equipped)
- Overview
- Location
- Lubricants
- Pump Display and Control Elements of Control Screen
- Pump Display Mode
- Pump Programming
- Maintenance
- Troubleshooting
- Inspection, Maintenance and Adjustment
- Maintenance Information
- Machine Setup Position for Maintenance
- Handling Oil, Fuel, DEF (AdBlue®), Coolant
- Oil
- Fuel
- DEF (AdBlue®)
- Grease
- Coolant and Water for Dilution
- Filters
- Electrical System Maintenance
- Recommend Fuel, Coolant, and Lubricant
- Lubrication
- Symbols for “Lubrication and Service Chart”
- Fluid Capacities
- Table of Recommended Lubricants
- Maintenance Intervals
- 10 Hour / Daily Service
- Boom, Arm and Front Attachment Pins – Lubricate
- Engine Oil Level – Check
- Hydraulic Oil Level – Check
- Fuel Level – Check
- DEF (AdBlue®) Tank Level- Check
- Fuel Prefilter and Water Separator – Check
- Additional Water Separator – Check
- Swing Reduction Gear Oil Level – Check
- Dust Net – Clean
- Coolant Level – Check
- Window Washer Liquid Level – Check
- Bucket Teeth and Side Cutters – Inspect
- Cooling Fan Blade – Inspect
- Air Intake System and Emission Control System – Check
- Seat Belt – Inspect
- AVM (Around View Monitoring system) – Check
- Mirrors – Check
- Structure – Inspect
- All Switches and Travel Alarm (If Equipped) – Check
- Safety Lever – Check
- Exterior Lights, Horn, Control Console Indicator, Gauge Panel – Check
- Overall of Engine Condition – Check
- All Controls and Linkages – Check
- 50 Hour / Weekly Service
- Perform All Daily Service Checks
- Arm and Bucket Joint Pins – Lubricate
- Swing Bearing – Lubricate
- Fuel Tank Water and Sediment – Drain
- Air Compressor and Tank – Check
- Engine Fan Belt – Check
- Track Assemblies (Links, Shoes, Rollers, Idlers) – Inspect
- 250 Hour / Monthly Service
- Perform All Daily and 50 Hour Service Checks
- Boom and Arm Joint Pins – Lubricate
- Engine Fan and Alternator Belts – Check
- Breaker Filter (If Equipped) – Replace
- Hydraulic Oil Return Filter – Replace
- Pilot Filter – Replace
- Drain Filter – Replace
- Pump Drive Gear Oil – Change
- Pin and Bushings of the Front End Attachment – Inspect
- Battery Fluid – Check
- Bolts and Nuts – Inspect
- Fuel System Hose Clamps – Inspect
- 500 Hour / 3 Month Service
- Perform All Daily, 50 and 250 Hour Service Checks
- Track Spring – Check
- Swing Gear and Pinion – Lubricate
- Engine Oil and Filter – Replace
- Air Compressor Filter (If Equipped) – Clean
- Air-conditioning Outer Filter – Clean
- Air-conditioning Inner Filter – Clean
- Cooling System – Clean
- Air Cleaner Outer Filter – Clean
- Fuel Prefilter and Water Separator – Replace
- Additional Water Separator (If Equipped) – Clean
- Main Fuel Filter – Replace
- Final Drive Gear Oil – Check
- Check Belt
- Final Drive Gear Oil – Change
- Swing Reduction Gear Oil – Change
- Fuel Cap Filter – Replace
- 1,000 Hour / 6 Month Service
- Perform All Daily, 50, 250 and 500 Hour Service Checks
- Swing Reduction Gear – Lubricate
- Hydraulic Oil Tank Breather Filter – Replace
- Hydraulic Oil Return Filter – Replace
- Pilot Filter – Replace
- Drain Filter – Replace
- Final Drive Gear Oil – Change
- Swing Reduction Gear Oil – Change
- Pump Drive Gear Oil – Change
- Air-conditioning Outer Filter – Replace
- Air-conditioning Inner Filter – Replace
- 2,000 Hour / Yearly Service
- Perform All Daily, 50, 250, 500 and 1,000 Hour Service Checks
- Air Cleaner Outer and Inner Filter – Replace
- Pump Drive Gear Oil – Change
- Coolant – Change
- Hydraulic Oil and Suction Filter – Replace
- Alternator and Starter** – Check
- Rubber Antivibration Shock Mounts – Check
- Perform and Record Results of Cycle Time Tests
- Inspect Machine to Check for Cracked or Broken Welds or other Structural Damage
- Adjust Valve Clearance** – Check
- Head Bolt Torques – Check
- 4,000 Hour / 2 Year Service
- Major Parts – Periodic Replacement
- 5,000 Hour / 2 Year and 6 Month Service
- DEF (AdBlue®) Filter – Replace
- DPF – Clean
- 12,000 Hour / 6 Year Service
- Hose In-service Lifetime Limit (European Standard ISO 8331 and EN982 (CEN))
- Air-conditioning System
- Gauge Panel – Check
- Air Conditioner Hoses – Check
- Condenser – Check
- Magnetic Clutch – Check
- Bucket
- Bucket Tooth – Replace
- Bucket O-ring – Replace
- Electrical System
- Engine Cooling System
- General
- Antifreeze Concentration Tables
- Table of Standards for Allowed Tap Water
- Fuel Transfer Pump (If Equipped)
- Removable Counterweight System (If Equipped)
- Counterweight Joint Pins – Lubricate
- Handling of Accumulator
- Track Tension
- Venting and Priming Hydraulic System
- Main Pump
- Cylinders
- Swing Motor
- Travel Motor
- General Venting
- Maintenance in Special Conditions
- Transportation
- Disassembly and Assembly Before and after Transportation
- Personnel and Equipment
- Disassembly and Reassembly
- Remove and Install Counterweight
- Track Frame Extension and Retraction
- Lifting the Machine Componets
- Upper Structure Swing Body
- Counterweight
- Arm with Bucket Cylinder
- Bucket
- Boom with Arm Cylinder
- Boom Cylinder
- Loading and Unloading
- Warning for Counterweight and Front Attachment Removal
- Specification
- Standard Specification
- Overall Dimensions
- Ground Pressure
- Digging Force
- Arm – Tearout Force
- Bucket – Breakout Force
- Working Range
- Excavator Rated Lift Capacity Tables
- Approximate Weight of Workload Materials
- Index
Develon
