Description
Fendt 12545 PRO Former Rotary Rake Operator’s Manual
Fendt 12545 PRO Former Rotary Rake Index:
Contents
1
Introduction
1.1
Warranty and liability
1.2
Conventions
1.2.1
Illustrations
Pictograms used
1.2.3 Text symbols
1.2.4 Abbreviations
1.3
Other applicable documentation
1.4
Storage of documentation
1.5
Applicability of the Operator’s Manual
1.6
Sign plate and serial number
1.7
EU Declaration of Conformity
2
Safety
2.1
Intended use
2.2
Reasonably foreseeable misuse
2.3
User qualifications
2.4
Warning notices
2.4.1 Warning notices in the Operator’s Manual
2.4.2 Warning notices on the machine
2.5 Safety instructions
Operating and maintenance personnel
Protective work wear
Personal protective equipment
Preparing the machine for use
Coupling/uncoupling the machine to/from the tractor
Machine operation
Driving on public roads and lanes
Maintenance work
Working with hydraulics
Work in the vicinity of high-voltage power lines
Unauthorized modifications or alterations
What to do in an emergency
Fire prevention
3 Machine description
3.1 Product features
3.2 Machine positions
3.2.1 Transport position
3.2.2 Working position
3.2.3 Headland position
3.2.4
Parking position
3.3 Notices on the machine
4
ISOBUS control systemDisplay layout
General buttons
Menus
Menu structure
“Main menu”
“Transport” menu
“Lifting/Lowering” menu
“Working Setup” menu
“On-Board Computer” menu
“User Setup” menu
“Manual Operation” menu
“Headland position” menu
“Calibrations” menu
“Diagnostics” menu
“Factory Settings” menu
4.4 Error messages
5
Technical data
5. I Machine data
5.2 Tires
5.3 Noise information
5.4 Axle loads, gross weight and minimum ballast required
6
Initial start-up
6. I Assembling the machine
6.2 Adjusting the transmission shaft
7
Using the machine
7.1 Attachment to the tractor
Stan-up
Coupling the machine
Fitting the transmission shaft
Connect the hydraulics
Connect the lighting
Connecting the ISOBIJS
Connect the air pressure brake
Releasing the parking brake
Road travel
Switching the machine to working position
Using the machine
7.4.1 Tuming at the end of the field
7.5 Switching the machine to transport position
7.6 Machine storage
7.7 Settings
7.7.1 Adjusting the swath width
Adjusting the height of the swath former
Adjusting the swath formation
Adjusting the lateral inclination
Adjusting the longitudinal inclination
Adjusting the sequential control
Setting the uo-rotor operation mode
Setting individual rotor operation mode
8 Special equipment
Rectifying faults
9.1 After hitting an obstacle
9.2 Emergency operation
Lifting rotors into the transport position
Lowering rotors into working position
Lifting rotors into the headland position
Setting the working Width in emergency operation
Setting the swath width in emergency operation
Setting the working height in emergency operation
Maintenance
Maintenance intervals
Cleaning
Tightening torques for nuts and bolts
Decals
Transmission shaft maintenance
Servicing the hydraulics
Brake system maintenance
10.7.1 Checking the thickness of the brake pads
10.7.2 Tightening brake cylinders
10.7.3 Drain the water from the compressed air reservoir
10.8 Gearbox maintenance
10.8.1 Checking gearbox GT-30 oil level
10.8.2 Checking gearbox GT-40 oil level
10.8.3 Checking transfer gearbox oil level
10.9 Tire maintenance
10.9.1 Changing wheels
10.9.2 Tire pressure
IO-IO Lubrication instructions
11 Decommissioning
11.1 Storage
11.2 Disposal
