John Deere 1032, 1042, 1052 and 1055 Combines Technical Manual (TM4413)

John Deere 1032, 1042, 1052 and 1055 Combines Technical Manual (TM4413)

John Deere 1032, 1042, 1052 and 1055 Combines  INDEX:

SECTION 10 – GENERAL
Group 05 — Specifications
Group IO — Testing and adjustments
SECTION 20 – ENGINE REPAIR
Group 05 — Removal and installation, 4-cyl. engine
Group IO— Removal and installation, 6-cyl. engine
SECTION 30 – FUEL AND AIR SYSTEM REPAIR
Group 05 — Fuel filter With water trap and electrical fuel transfer pump
SECTION 40 – ELECTRICAL SYSTEM REPAIR
Group 05 — Wiring harnesses and connectors
Group IO — Starting motor (to Serial No, N9283)
Group 1 — Starting motor (from Serial No. 049284)
Group 15 — Alternator (65 A)
Group 16 — Alternator (95 A)
— System components
Group 25 — Low shaft speed monitor system
Group 30— Electromagnetic transmission brake
SECTION 50 – POWER TRAIN
Group 05 — Variable ground speed drive
Group IO — Engine clutch and mechanical clutch
operation (3-speed transmission)
Group 1 1 — Engine clutch and hydraulic clutch
operation (3-speed transmission)
15 — Engine clutch operation
(4-speed transmission)
Group 16 — Clutch operating system
(4-speed transmission, from Serial No. 049593)

SECTION 50 – POWER TRAIN (Contd.)
Group 20 — Engine clutch (4-speed transmission)
Group 21 — Engine clutch (4-speed transmission,
from Serial No. 044137)
Group 25 — Three-speed transmission
Group 30 — Four-speed transmission
Group 35 — Final drives, differential
(3-speed transmission)
Group 40 — Final drives, differential
(4-speed transmission)
Group 45 – drive on rice combine
(4-speed transmission)
Grow) 50 — Track system
SECTION 60 – BRAKES, REAR AXLE AND STEERING
Group 05 — Parking brake (3-speed transmission)
Group IO — Parking brake (4-speed transmission)
Group 15 — Brake operation
Group 20 — Foot brakes (3-speed transmission)
Group 25 — Foot brakes (4-spood transmission)
GrotQ 26 — Foot brakes with integrated slave
cylinder (rice combine)
Grot-Q 30 — Rear axle
35 — V-support for Wide rear axle
Group 40 — Hydrostatic steering unit
Group 45 — Steering cylinder
SECTION 70 – HYDRAULIC SYSTEM REPAIR
Group 05 — Hydraulic oil reservoir and lines
Group IO — Hydraulic pump
Group 15 — 3- and 4-spool control valves
with flow divider
Group 20 — Hydraulic cylinders
Group 2S — Nitrogen accumulators

SECTION 80- MISCELLNEOUS
SECTION 130 – GRAIN PROCESSING
Group 05 — Bearings and shafts
Group IO — Drive belts
Group 15 — Drive chains
SECTION 90 – OPERATOR’S PLATFORM WITH CAB
Group 40 — Riser tube
Group 04 — Stone trap
Group 20 — Concave
Group 05 — Cab ventilation system
— Safe handling of refrigerants
Group 15 — Air conditioning compressor
Group 20 — Air conditioning system service
and tests
Group 25 — Air conditioning system components
Group 30
— Cab heating system
Group 35 – Operator’s seat
Group 40 — Operator’s cab
Group 45 — Platform control levers
SECTION 100- CUTTING PLATFORM AND CORA HEAD
Group 05 — Cutting platform and knife drive
Group 10 — Cutting platform auger
Group 15 — Variable reel speed drive
Group 20 — Corn head
Group 25 — Corn head gear case
SECTION 110 – FEEDER HOUSE
Group 05 — Feeder drive
Group IO — Feeder with integrated platform
Group 15 — Feeder With quick-tach platform
SECTION 120- SEPARATOR AND CLEANING UNIT
Group 05 — Separator drive
Group 10 — Variable cylinder drive
Group 15 — Threshing cylinder
Group 25 — Beater variable drive
Beater
Group 35 — Cross shaker
Group 40 — Straw walkers
Group 45 — Cleaning shoe and sieves
Group 50— Fan and variable tan drive
— Clean grain and tailings augers
Group 10 — Cean grain elevator
— Tailings elevator
upper tailings auger
Group 25 — Grain tank leveling auger
Grain tank center fill auger
Group 30 –
Group 35 — Inner grain tank unloading auger
Group 45 — Discharge tube
SECTION 140 – SPECIAL EQUIPMENT
Group 05 — Straw chopper drive
Group 06 — Straw chopper fiect drive
Group 10 — Straw chopper rotor bearings
SECTION 230- FUEL SYSTEM –
OPERATION AND TESTS
Group 05 — Fuel filter with water trap
and electrical fuel transfer pump
SECTION 240 – ELECTRICAL SYSTEM – OPERATION AND TESTS
Group 05 — Electrical circuit and wiring diagrams
Group 06 — Circuit testing
Group 10 — Starting motor
Group 15 — Alternator
SECTION 250 – POWER TRAIN –
OPERATION AND TESTS
Group 05 — Clutch and mechanical clutch
operation (3-speed transmission)
Group 06 — Clutch and hydraulic clutch
operation (3-speed transmission)
Group IO — outch operation (4-speed transmission)
Group IS — Clutch (4-speed transmission)
Group 20 Three-speed transmission
Group 25 — Four-speed transmission

John Deere