John Deere 1410D Forwarder Index:

• Contents
  • Introduction
    • Operator’s manual for Timberjack 1410D Forwarder
    • Foreword
    • Timberjack Contact Information
    • Technical Information Feedback Form
  • Warranty[scWarranty[ec
    • Standard warranty clauses
    • 250 Hour Service
  • Safety – Safety Features
    • 1410D Forwarder Safety Features
  • Safety – General Precautions
    • General
    • Recognize Safety Information
    • Understand Signal Words
    • Replace Safety Signs
    • Maintain Safety Cabin
    • Driving and Service
    • Use of Radio-transmitters
    • Prepare for Emergencies
    • Handle Fluids Safely—Avoid Fires
    • Handle Chemical Products Safely
    • Dispose of waste properly
    • Avoid High-Pressure Fluids
    • Wear Protective Clothing
    • Daily checks
  • Safety – Operating Precautions
    • General operating instructions
    • Handle Starting Fluid Safely
    • Controls
    • Alarms
    • Secondary exit
    • Travel Safely
    • Do Not Short Starter
    • Operating the Machine
    • Loading the Machine
    • Driving on Frozen Water
    • Driving/Transporting on Public Roads
    • Power Cables
    • Fire Prevention
    • What To Do If the Machine Catches Fire
  • Safety – Maintenance Precautions
    • Service Machines Safely
    • Using the Xenon Worklamp
    • Securing the Service Position
    • Fluids
    • Prevent Acid Burns
    • Service Cooling System Safely
    • Prevent Battery Explosions
    • Service Tires Safely
    • Work in Clean Area
    • Illuminate Work Area Safely
    • Use Proper Tools
    • Use Proper Lifting Equipment
  • Operator’s Station
    • General
    • Front Dashboard
    • Start Key Positions
    • Window Washers and Wipers
    • Signal Lights
    • Left Arm Control Panel
    • Right Arm Control Panel
    • Using Boom Control Levers
    • Overhead Panel Switches
    • Warning Lamps and Buzzer
    • Preparedness for telephone
    • Air Conditioner Controls
    • Operator’s seat
  • Operating the Machine, Control System
    • TMC
    • ECU
    • Alarms
  • Operating the machine, Operation
    • Function of Seat Safety Switch
    • Emergency Stopper
    • Operating the Boom
    • Brakes
    • Frame Brake
    • Steering
    • High/Low Gear and Rear-Wheel Drive
    • Using the Differential Lock-Up
    • Operating the Decking Blade (Optional Equipment)
    • Operating the Clambunk
  • Lifting and Lowering the Cab
    • How to Lift the Cab
    • How to Lower the Cab
  • Transportation of the Machine
    • Use hold-down straps
    • Positioning
    • Minilevers
    • Chains
  • Starting and Turning Off the Engine
    • Before Starting the Engine for the First Time in a Working Day
    • Normal Start
    • Cold engine starting
    • After starting
    • A normal operation of the engine
    • Turning off the engine
  • Driving the Machine
    • Off-Road Driving
    • Driving on Road
  • Towing the Machine
    • Towing
    • Stowing a Disabled Boom
  • Maintenance – Machine
    • Service, General
    • Servicing Safety Precautions
    • General Maintenance Instructions
    • Welding Instructions
    • Cleaning the Cab windows
    • Tires
    • Changing Wheels
    • Anti slips
    • Fitting bogie tracks
    • Recommended Lubricants and Fluids
    • Capacities
    • Diesel Fuel
    • Engine Oil
    • Coolant
    • Hydraulic oil
    • Gear oil
    • Brake fluid
    • Cab lift pump
    • Grease
  • Maintenance – Periodic
    • Maintenance intervals
  • Maintenance – Every 10 hours or Daily
    • Check the hydraulic oil level
    • Check the engine oil level
    • Check the Fuel Pre-Filter
    • Check engine coolant level.
    • Check the windshield washer fluid level
    • Check the radiator grille cleanness
    • Check the driving brake oil level
    • Check the air filter
    • Check the tires for air pressure and overall shape.
    • Fill up the fuel tank
    • Maintain the boom
    • The following service and checks are to be made at the end of each workday
  • Maintenance – Every 50 hours or Weekly
    • Grease the center hinge bearings and steering cylinder bearings.
    • Grease the decking blade1
    • Check the air conditioner
    • Maintain the Boom
    • Check the fire extinguisher system
  • Maintenance – Every 250 hours
    • Clean the machine
    • Check the high/low gear oil level.
    • Check Differential Oil Level
    • Check Single Axle Wheel Ends ( Hub gear) Oil Level
    • Check Bogie Housings Oil Level
    • Grease Bogie Bearings
    • Check Wheel Nut Torque
    • Check the cabine air filters
    • Check the air conditioner
    • Maintain the boom
  • Maintenance – Every 500 hours
    • Change engine oil and replace oil filter
    • Change the fuel filters
    • Clean crankcase vent tube
    • Check the air intake system
    • Checking belt tensioner spring tension and belt wear
    • Check engine speeds
    • Control engine grounding
    • Remove sediment and water from the fuel tanks
    • Renew the pressure filter of the drive hydraulic system
    • Check the batteries for charge
    • Checking cooling system
    • Control of the diesel engine coolant
    • Filling supplemental coolant additives (SCA) between coolant changes
    • Pressure control of the cooling system
    • Grease the driveshafts
  • Maintenance – Every 1000 hours
    • Renew the hydraulic oil.
    • Replace the hydraulic return filter
    • Replace the hydraulic tank breather
    • Renew the high/low gear (transfer case) oil
    • Check and tighten the screw and bolt connections
    • Check the exhaust manifold
    • Check the air conditioner
    • Maintain the boom
  • Maintenance – Every 2000 hours
    • Check Valve Clearance – Engines (200,000- )
    • Checking Crankshaft Vibration Damper
    • Changing the Coolant
    • Change Bogie Axle Differential Oil
    • Change Bogie Housings Oil
    • Change Single Axle Differential Oil
    • Change Single Axle Wheel Ends Oil
    • Check and tighten the bolts for the joints between axles and frame
  • Maintenance – Every 6 months
    • Service the fire extinguisher
  • Maintenance – Every 12 months
    • Have the fire extinguisher system (opt. eq.) checked
  • Maintenance – As required
    • General
    • Bleeding the fuel system
    • Have the proper function of the turbocharger checked
    • Have the proper function of the alternator checked
    • Have the proper function of the starter motor checked
    • Have the proper function of the atomizers checked
    • Clean the Fuel Tank Filler Filter
    • Replacing fan/alternator belt
    • Maintain the Boom
    • Check the air conditioner
  • Cooling System Maintenance
    • Replenishing Supplemental Coolant Additives (SCAs) Between Coolant Changes
    • Pressure Testing Cooling System
  • Hydraulic System: Hydraulic Oil Change
    • Hydraulic tank and the vacuum pump
    • Checking the oil level in hydraulic tank
    • Renew the hydraulic oil.
  • Hydraulic System: General
    • Working hydraulic system
    • Hydrostatic system
  • Hydraulic System: Bleeding
    • General
    • Bleeding Drive Hydraulic System
    • Bleeding Work Hydraulic System
    • Bleeding the Brake System
  • Hydrostatic System: Drive Pump adjusting
    • Checking and adjusting the charge pressure
    • Checking and adjusting the pressure cut-off valve setting of the drive pump
  • Hydrostatic System: Drive Motor adjusting
    • Checking the function of hydrostatic flushing valve
    • Checking and adjusting drive motors pressure cut-off settings
  • Work Hydraulic System: Check and Adjust
    • Adjustment of Pressure Difference
    • Adjusting the Maximum Pressure
    • Adjusting the Boom Pressure
    • Adjusting Auxiliary Functions
    • Adjusting Frame Brake
    • Adjusting Proportional Decking Blade
    • Adjusting Optional Equipment
  • Brake System: Check and Adjust
    • Checking the brakes
    • Mechanical adjustment of brakes
    • Brake Charging Pressure
    • Checking the Work Brake
    • Checking the Drive Brake (Brake Pedal)
  • Electrical System
    • Main Switch
    • Location of ECU and engine sensors
    • Batteries
    • Welding
    • Fuses on the Left-Hand Side in the Engine Compartment
    • Instrument Box Fuses and Relays
    • The RPM Sensor of the Drive Hydrostatics Motor
    • Hydraulic Tank Sensors
  • Transmission
    • Operating Power Transmission
    • High/Low Gear
    • Hydrostatic System
    • Control of Transmission
  • Boom, General
    • A General Description of the Boom
    • Operating Safety Precautions
    • General Operating Instructions
  • Boom Maintenance, General
    • Assembly Instructions
    • Bleeding the Hydraulic System
    • Maintenance Schedule
  • Boom, Maintenance every 10 hours
    • Grease the grapple and link.
    • Check boom structures
    • The following service and checks are to be made at the end of each workday
  • Boom, Maintenance every 50 hours
    • Check the boom slewing housing oil level
    • Check that the joint pins of the boom are secured.
    • Check the sideways clearance of the extension booms.
    • Check the boom extension boom chains for tightness.
    • Grease the rocker and cylinder bearings of the boom and the slewing system bearing.
    • Lubricate the extension boom chains with oil.
    • Check the grapple
    • Lubrication and Maintenance Chart
  • Boom, Maintenance every 250 hours
    • Clean the boom.
    • Check boom structures
    • Check the extension booms for vertical clearance.
    • Check the tightness of boom fastening bolts, hydraulic cylinder covers, and other screw joints
  • Boom, Maintenance every 1000 hours
    • Clean the magnetic plug of rotator
    • Change the boom slewing system oil
    • Clean the boom extension boom chains (depending on the model)
  • Boom, Maintenance as required
    • Adjusting the rotator link brakes
  • Boom, Technical Data
    • Boom CF7
    • Rotator and Grapple
    • Boom CF7
  • Equipment, Air Conditioner
    • Introduction
    • Main Parts of Air Conditioning System
    • Risks and Counter-Measures
    • First Aid
    • Air Conditioner, Using
    • Maintenance and Inspections: Check the refrigerant level.
    • Check the service moisture indicator of the dryer every 50 hours
    • Service the compressor V-belt every 250 hours
    • Service the compressor every 1000 hours
    • Service the evaporator element every 1000 hours
    • Service the condenser element every 1000 hours
    • Service the hoses and connectors every 1000 hours
  • Equipment, Engine Preheater
    • Operation and maintenence
  • Equipment, Fire Extinguisher System
    • General
    • Fire Alarm and Actions
    • After a fire
    • Control unit
    • Hand-held fire extinguishers
  • Equipment, Decking Blade
    • Using the Decking Blade
    • Lowering the Decking Blade
    • Decking Blade’s Float
  • 1410D Specifications
    • Dimensions
    • Decals and Signs
    • Load area
    • Engine
    • Transmission
    • Axles
    • Steering
    • Brakes
    • Hydraulic system
    • Electrical System
    • Boom
    • Cab
  • Hydraulic Diagrams, F622627
    • Hydraulic Diagrams, F622627
    • Boom Hydraulics
    • Transmission Hydraulics
    • Brake Hydraulics
    • Extra Equipment Hydraulics
    • Options Hydraulics
  • Wiring Diagrams, 1410D
    • General
  • TMC
    • TMC CONTROL SYSTEM ver 3G+
• Page Numbers
  • Section 1-1
    • 1
    • 2
    • 3
  • Section 2-1
    • 1
  • Section 3-1
    • 1
  • Section 3-2
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
    • 7
  • Section 3-3
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
    • 7
    • 8
    • 9
  • Section 3-4
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
    • 7
    • 8
  • Section 4-1
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
    • 7
    • 8
    • 9
    • 10
    • 11
    • 12
  • Section 5-1
    • 1
    • 2
  • Section 5-2
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
    • 7
  • Section 5-3
    • 1
    • 2
  • Section 5-4
    • 1
    • 2
  • Section 5-5
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
  • Section 5-6
    • 1
    • 2
    • 3
  • Section 5-7
    • 1
    • 2
    • 3
    • 4
    • 5
  • Section 6-0
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
    • 7
    • 8
    • 9
    • 10
    • 11
    • 12
    • 13
    • 14
    • 15
    • 16
    • 17
  • Section 6-1
    • 1
    • 2
  • Section 6-2
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
    • 7
    • 8
  • Section 6-3
    • 1
    • 2
    • 3
  • Section 6-4
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
    • 7
    • 8
  • Section 6-5
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
    • 7
    • 8
    • 9
    • 10
    • 11
  • Section 6-6
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
  • Section 6-7
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
    • 7
    • 8
    • 9
    • 10
    • 11
  • Section 6-8
    • 1
  • Section 6-9
    • 1
  • Section 6-10
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
  • Section 6-11
    • 1
    • 2
    • 3
  • Section 7-1
    • 1
    • 2
    • 3
  • Section 7-2
    • 1
  • Section 7-3
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
    • 7
  • Section 7-4
    • 1
    • 2
  • Section 7-5
    • 1
    • 2
    • 3
  • Section 7-6
    • 1
    • 2
    • 3
    • 4
    • 5
  • Section 7-7
    • 1
    • 2
    • 3
    • 4
  • Section 8-1
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
    • 7
    • 8
    • 9
    • 10
  • Section 9-1
    • 1
    • 2
    • 3
  • Section 10-0
    • 1
    • 2
    • 3
    • 4
    • 5
  • Section 10-1
    • 1
    • 2
  • Section 10-2
    • 1
    • 2
  • Section 10-3
    • 1
    • 2
    • 3
    • 4
  • Section 10-4
    • 1
    • 2
  • Section 10-5
    • 1
    • 2
  • Section 10-6
    • 1
  • Section 10-7
    • 1
    • 2
    • 3
    • 4
  • Section 11-1
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
    • 7
    • 8
    • 9
    • 10
    • 11
    • 12
    • 13
  • Section 11-2
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
    • 7
    • 8
    • 9
  • Section 11-3
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
    • 7
    • 8
  • Section 11-4
    • 1
    • 2
    • 3
  • Section 12-0
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
    • 7
  • Section Hydraulic Diagrams
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
    • 7
    • 8
    • 9
    • 10
    • 11
    • 12
    • 13
  • Section Wiring Diagrams
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6
    • 7
    • 8
    • 9
    • 10
    • 11
    • 12
    • 13
    • 14
    • 15
    • 16
    • 17
    • 18
    • 19
    • 20
    • 21
    • 22
    • 23
    • 24
    • 25
    • 26
    • 27
    • 28
    • 29
    • 30
    • 31
    • 32
    • 33
    • 34
  • Section TMC
    • 1