Komatsu PC1000-1, PC1000LC-1, PC1000SE-1 Hydraulic Excavator Index:

• COVER
• 1.FOREWORD
• 2.SAFETY INFORMATION
• 3.INTRODUCTION
• 4.LOCATION OF PLATES,TABLE TO ENTER SERIAL NO. AND DISTRIBUTOR
• 5.CONTENTS
• SAFETY
  • 6.GENERAL PRECAUTIONS
  • 7.PRECAUTIONS DURING OPERATION
    • 7.1 BEFORE STARTING ENGINE
    • 7.2 OPERATING MACHINE
    • 7.3 TRANSPORTATION
    • 7.4 BATTERY
    • 7.5 BUCKET WITH HOOK
  • 8.PRECAUTIONS FOR MAINTENANCE
    • 8.1 BEFORE CARRYING OUT MAINTENANCE
    • 8.2 DURING MAINTENANCE
  • 9.POSITION FOR ATTACHING SAFETY LABELS
• OPERATION
  • 10.GENERAL VIEW
    • 10.1 GENERAL VIEW OF MACHINE
    • 10.2 GENERAL VIEW OF CONTROLS AND GAUGES
  • 11.EXPLANATION OF COMPONENTS
    • 11.1 MACHINE MONITOR
    • 11.2 LAMP
    • 11.3 SWITCHES
    • 11.4 CONTROL LEVERS, PEDALS
    • 11.5 CEILING WINDOW
    • 11.6 FRONT WINDOW
    • 11.7 DOOR LOCK
    • 11.8 DUST INDICATOR
    • 11.9 AIR CONDITIONER
    • 11.10 RADIO
    • 11.11 FUSE
    • 11.12 CONTROLLERS
    • 11.13 TOOL BOX
    • 11.14 GREASE PUMP
    • 11.15 HANDLING GREASE PUMP
    • 11.16 HANDLING ACCUMULATOR
  • 12.OPERATION
    • 12.1 CHECK BEFORE STARTING ENGINE
    • 12.2 STARTING ENGINE
    • 12.3 OPERATIONS AND CHECKS AFTER STARTING ENGINE
    • 12.4 MOVING MACHINE OFF
    • 12.5 STEERING MACHINE
    • 12.6 STOPPING MACHINE
    • 12.7 SWINGING
    • 12.8 OPERATION OF WORK EQUIPMENT
    • 12.9 WORKING MODE SELECTION
    • 12.10 PROHIBITIONS FOR OPERATION
    • 12.11 PRECAUTIONS FOR OPERATION
    • 12.12 PRECAUTIONS WHEN TRAVELING UP OR DOWN HILLS
    • 12.13 HOW TO ESCAPE FROM MUD
    • 12.14 WORK POSSIBLE USING HYDRAULIC EXCAVATOR
    • 12.15 PARKING MACHINE
    • 12.16 CHECK AFTER FINISHING WORK
    • 12.17 STOPPING ENGINE
    • 12.18 CHECK AFTER STOPPING ENGINE
    • 12.19 LOCKING
  • 13.TRANSPORTATION
    • 13.1 PRECAUTIONS FOR TRANSPORTATION
    • 13.2 PARTS FOR TRANSPORT
    • 13.3 PROCEDURE FOR INCREASING OR REDUCING TRACK FRAME GAUGE
  • 14.COLD WEATHER OPERATION
    • 14.1 PRECAUTIONS FOR LOW TEMPERATURE
    • 14.2 PRECAUTIONS AFTER COMPLETION OF WORK
    • 14.3 AFTER COLD WEATHER
  • 15.LONG-TERM STORAGE
    • 15.1 BEFORE STORAGE
    • 15.2 DURING STORAGE
    • 15.3 AFTER STORAGE
    • 15.4 STARTING MACHINE AFTER LONG-TERM STORAGE
  • 16.TROUBLESHOOTING
    • 16.1 PHENOMENA THAT ARE NOT FAILURES
    • 16.2 PRECAUTIONS ON PARTICULAR JOBSITES
    • 16.3 IF BATTERY IS DISCHARGED
    • 16.4 OTHER TROUBLE
• MAINTENANCE
  • 17.GUIDES TO MAINTENANCE
  • 18.OUTLINES OF SERVICE
    • 18.1 OUTLINE OF OIL,FUEL,COOLANT
    • 18.2 OUTLINE OF ELECTRICAL SYSTEM
    • 18.3 OUTLINE OF HYDRAULIC SYSTEM
    • 18.4 RELEASING PRESSURE
    • 18.5 BLEEDING AIR FROM CIRCUIT
    • 18.6 OIL FILTER AND LEVEL GAUGE POSITIONS
  • 19.CONSUMABLE PARTS LIST
  • 20.USE OF FUEL,COOLANT AND LUBRICANTS ACCORDING TO AMBIENT TEMPERATURE
  • 21.STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS
    • 21.1 INTRODUCTION OF NECESSARY TOOLS
    • 21.2 TORQUE LIST
  • 22.PERIODIC REPLACEMENT OF CRITICAL SAFETY PARTS
  • 23.MAINTENANCE SCHEDULE CHART
    • 23.1 MAINTENANCE SCHEDULE CHART
  • 24.SERVICE PROCEDURE
    • 24.1 INITIAL 100 HOURS SERVICE
    • 24.2 INITIAL 250 HOURS SERVICE
    • 24.3 WHEN REQUIRED
    • 24.4 CHECK BEFORE STARTING
    • 24.5 EVERY 10 HOURS SERVICE
    • 24.6 EVERY 100 HOURS SERVICE
    • 24.7 EVERY 250 HOURS SERVICE
    • 24.8 EVERY 500 HOURS SERVICE
    • 24.9 EVERY 1000 HOURS SERVICE
    • 24.10 EVERY 2000 HOURS SERVICE
    • 24.11 EVERY 4000 HOURS SERVICE
• SPECIFICATIONS
  • 25.SPECIFICATIONS
• OPTIONS,ATTACHMENTS
  • 26.GENERAL PRECAUTIONS
    • 26.1 PRECAUTIONS RELATED TO SAFETY
    • 26.2 PRECAUTIONS WHEN INSTALLING ATTACHMENTS
  • 27.HANDLING BUCKET WITH HOOK
    • 27.1 CHECKING FOR DAMAGE TO BUCKET WITH HOOK
    • 27.2 PROHIBITED OPERATIONS
    • 27.3 PRECAUTIONS DURING OPERATIONS
  • 28.USING SEAT BELT
    • 28.1 SEAT BELT
  • 29.INTRODUCTION OF ATTACHMENTS
    • 29.1 SPECIFICATION,USE
• BACK HOE TYPE SHOVEL
  • 30.GENERAL LOCATIONS
  • 31.INSTRUMENTS AND CONTROLS
    • 31.1 SWITCH
    • 31.2 CONTROL LEVERS
    • 31.3 CONTROL BOX
    • 31.4 FUSE BOX
  • 32.OPERATION
    • 32.1 OPERATION OF WORK EQUIPMENT
    • 32.2 CHECK BEFORE STARTING ENGINE
  • 33.PRECAUTIONS FOR MACHINE OPERATION
    • 33.1 PRECAUTONS DURING OPERATION
  • 34.PRECAUTIONS WHEN DISASSEMBLING MACHINE
  • 35.MAINTENANCE
    • 35.1 OIL FILLER AND LEVEL GAUGE POSITION
    • 35.2 ADJUST BUCKET CLEARANCE
    • 35.3 CHECK BEFORE STARTING
    • 35.4 EVERY 10 HOURS SERVICE
  • 36.EXCAVATOR WORK
  • 37.TRANSPORTATION
  • 38.INTRODUCTION OF ATTACHMENTS
    • 38.1 ATTACHMENT INSTALLATION COMBINATION TABLE
    • 38.2 SPECIFICATION,USE
  • 39.SPECIFICATIONS