Komatsu PC130-11 Hydraulic Excavator Operation and Maintenance Manual (TEN01047-02)
On a PC130-11 that’s digging foundations, loading trucks, or doing utility work around streets and tight sites, this Operation and Maintenance Manual is what I use to keep the machine predictable and available. It lays out a sensible rhythm for daily checks, scheduled services, and inspections so you can catch loosened hardware, hose rubs, or odd hydraulic behavior before they turn into downtime. If, for example, the boom starts moving a little jerky on a cold morning, I’d use this book to verify the basic checks, warm‑up procedure, and inspection points before chasing more complex faults.
Applications & Use Cases
- Plan preventive maintenance so filters, pins, and wear parts are serviced before they cause failures.
- Structure daily walk‑arounds to spot leaks, cracked guards, loose steps, and track issues early.
- Verify correct operating practices when swapping operators or training a new hand.
- Trace performance complaints (slow cycle times, weak travel, odd noises) through logical inspection steps.
- Coordinate shop visits by logging hours and tasks straight from the manual’s service guidance.
FAQ
Q: Can I keep this manual on a tablet in the cab?
A: Yes, as long as the file is readable offline; it’s handy for quick checks between shifts.
Q: Is it worth printing sections of this manual?
A: I’d print the inspection and service interval pages and post them in the shop to keep everyone on the same schedule.
Safety Note
Always follow the manual’s safety procedures before inspecting, adjusting, or working around the machine.
Komatsu PC130-11 Hydraulic Excavator Index:
- COVER
- FOREWORD
- CONTENTS
- READ THIS MANUAL
- SAFETY INFORMATION
- INTRODUCTION
- MAIN USE OF MACHINE
- DIRECTIONS OF MACHINE
- VISIBILITY FROM OPERATOR’S SEAT
- ENGINE TECHNOLOGY TO CONFORM EXHAUST GAS EMISSION
- PRODUCT INFORMATION
- LOCATION OF PRODUCT IDENTIFICATION NUMBER (PIN) AND MACHINE SERIAL NO. PLATE
- LOCATION OF ENGINE NUMBER PLATE
- SERVICE METER LOCATION
- YOUR MACHINE SERIAL NUMBERS AND DISTRIBUTOR
- ABBREVIATION LIST
- SAFETY
- SAFETY LABELS
- LOCATION OF SAFETY LABELS
- CONTENTS OF SAFETY LABELS
- GENERAL PRECAUTIONS COMMON TO OPERATION AND MAINTENANCE
- PRECAUTIONS BEFORE STARTING OPERATION
- PREPARATIONS FOR SAFE OPERATION
- PRECAUTIONS TO PREVENT FIRE
- PRECAUTIONS WHEN GETTING ON OR OFF MACHINE
- DO NOT GET CAUGHT IN WORK EQUIPMENT
- PRECAUTIONS RELATED TO PROTECTIVE STRUCTURES
- PROTECTION AGAINST FALLING, FLYING OR INTRUDING OBJECTS
- UNAUTHORIZED MODIFICATION
- PRECAUTIONS RELATED TO ATTACHMENTS AND OPTIONS
- QUICK COUPLER ATTACHMENT
- LARGE ATTACHMENTS AND COMBINATIONS
- PRECAUTIONS RELATED TO CAB GLASS
- PRECAUTIONS WHEN RUNNING ENGINE INSIDE BUILDING
- PRECAUTIONS FOR OPERATION
- PRECAUTIONS FOR JOBSITE
- START ENGINE
- PRECAUTIONS FOR OPERATION
- PRECAUTIONS FOR TRANSPORTATION
- TOWING AND BEING TOWED
- LIFTING OPERATION BY USING BUCKET WITH HOOK
- PRECAUTIONS FOR MAINTENANCE
- PRECAUTIONS BEFORE STARTING INSPECTION AND MAINTENANCE
- PRECAUTIONS FOR CHECK AND MAINTENANCE
- PRECAUTIONS FOR DEF
- GENERAL CHARACTER AND PRECAUTIONS FOR HANDLING
- PRECAUTIONS FOR ADDING
- PRECAUTIONS FOR STORING
- PRECAUTIONS FOR FIRE HAZARD AND LEAKAGE
- OTHER PRECAUTIONS
- OPERATION
- GENERAL VIEW
- MACHINE EQUIPMENT NAME
- CAB EQUIPMENT NAMES
- CONTROLS AND GAUGES NAMES
- EXPLANATION OF COMPONENTS
- EXPLANATION OF MACHINE MONITOR EQUIPMENT
- SWITCHES
- CONTROL LEVERS AND PEDALS
- OTHER EQUIPMENT
- MACHINE OPERATIONS AND CONTROLS
- CHECKS AND ADJUSTMENT BEFORE STARTING ENGINE
- METHOD FOR STARTING ENGINE
- METHOD FOR OPERATIONS AND CHECKS AFTER STARTING ENGINE
- STOP ENGINE
- START MACHINE (TRAVEL FORWARD AND REVERSE) AND STOP MACHINE
- METHOD FOR STEERING MACHINE
- SWING MACHINE
- OPERATE WORK EQUIPMENT
- HANDLE WORKING MODE
- PROHIBITED OPERATIONS
- PRECAUTIONS FOR OPERATION
- PRECAUTIONS WHEN YOU OPERATE MACHINE ON SLOPES
- METHOD FOR ESCAPING FROM MUD
- RECOMMENDED APPLICATIONS
- EFFECTIVE USE OF HYDRAULIC EXCAVATOR
- METHOD FOR REPLACING AND INVERTING BUCKET
- PARK MACHINE
- METHOD FOR CHECKING AFTER FINISHING WORK
- LOCK
- HANDLE AIR CONDITIONER
- EXPLANATION OF AIR CONDITIONER EQUIPMENT
- METHOD FOR OPERATING AIR CONDITIONER
- RADIO
- EXPLANATION OF RADIO EQUIPMENT
- METHOD FOR CONTROLLING RADIO
- STOW ANTENNA
- HANDLE ROAD LINERS
- RECOMMENDED USE OF ROAD LINERS
- COMPARISON OF ROAD LINERS AND STEEL SHOES
- WARRANTY OF ROAD LINERS
- PRECAUTIONS WHEN USING ROAD LINERS
- HANDLE ANCHOR POINT FOR TIE-OFF
- TRANSPORTATION
- PRECAUTIONS FOR TRANSPORTING MACHINE
- SELECT TRANSPORTATION METHOD
- LOADING AND UNLOADING WITH TRAILER
- LIFT MACHINE
- COLD WEATHER OPERATION
- COLD WEATHER OPERATION INFORMATION
- PRECAUTIONS AFTER DAILY WORK COMPLETION IN COLD WEATHER
- AFTER COLD WEATHER SEASON
- PRECAUTIONS FOR LONG-TERM STORAGE
- PREPARATION FOR LONG-TERM STORAGE
- MAINTENANCE DURING LONG-TERM STORAGE
- TRAVEL MACHINE AFTER LONG-TERM STORAGE
- TROUBLES AND ACTIONS
- ACTIONS WHEN YOU RUN OUT OF FUEL
- PHENOMENA THAT ARE NOT FAILURES
- PRECAUTIONS FOR TOWING MACHINE
- PRECAUTIONS FOR SEVERE JOB CONDITION
- PRECAUTIONS FOR DISCHARGED BATTERY
- OTHER TROUBLE
- MAINTENANCE
- PRECAUTIONS FOR MAINTENANCE
- CHECK SERVICE METER READING
- KOMATSU GENUINE REPLACEMENT PARTS
- KOMATSU GENUINE LUBRICANTS
- ALWAYS USE CLEAN WASHER FLUID
- FRESH AND CLEAN LUBRICANTS
- CHECK DRAINED OIL AND USED FILTER
- PRECAUTIONS FOR REFILLING OIL OR FUEL
- PRECAUTIONS FOR ADDING DEF
- PRECAUTIONS FOR WELDING
- DO NOT DROP THINGS INSIDE MACHINE
- BURN PREVENTION
- DUSTY JOBSITES
- AVOID MIXING OIL
- LOCK INSPECTION COVERS
- BLEED AIR FROM HYDRAULIC CIRCUIT
- PRECAUTIONS WHEN INSTALLING HYDRAULIC HOSES
- CHECKS AFTER INSPECTION AND MAINTENANCE
- FUEL AND LUBRICANTS TO MATCH THE AMBIENT TEMPERATURE
- CLOSE ENGINE HOOD SECURELY
- HANDLE ANCHOR POINT FOR TIE-OFF
- PRECAUTIONS WHEN YOU CLEAN WORK EQUIPMENT CONTROL LEVER
- OUTLINE OF MAINTENANCE
- HANDLE OIL, FUEL, COOLANT, AND PERFORMING OIL CLINIC
- BATTERY TERMINAL
- ELECTRICAL COMPONENTS
- STANDARD TIGHTENING TORQUE FOR BOLTS AND NUTS
- MAINTENANCE SCHEDULE
- MAINTENANCE SCHEDULE TABLE
- MAINTENANCE INTERVAL FOR HYDRAULIC BREAKER
- MAINTENANCE PROCEDURE
- WHEN REQUIRED
- CHECK BEFORE YOU START OPERATION
- EVERY 100 HOURS MAINTENANCE
- EVERY 250 HOURS MAINTENANCE
- EVERY 500 HOURS MAINTENANCE
- EVERY 1000 HOURS MAINTENANCE
- EVERY 2000 HOURS MAINTENANCE
- EVERY 4000 HOURS MAINTENANCE
- EVERY 4500 HOURS MAINTENANCE
- EVERY 5000 HOURS MAINTENANCE
- EVERY 8000 HOURS MAINTENANCE
- EVERY 9000 HOURS MAINTENANCE
- SPECIFICATIONS
- ATTACHMENTS AND OPTIONS
- GENERAL PRECAUTIONS
- HANDLE ANCHOR POINT FOR TIE-OFF
- HANDLE BUCKET WITH HOOK
- PRECAUTIONS FOR OPERATION
- HANDLE MACHINE READY FOR INSTALLATION OF ATTACHMENT
- EXPLANATION OF COMPONENTS ON MACHINES WITH ATTACHMENT
- METHOD FOR CHANGE-OVER AND CONNECT HYDRAULIC CIRCUIT FOR MACHINE READY FOR INSTALLATION OF ATTACHMENT
- METHOD FOR REMOVING AND INSTALLING ATTACHMENT
- OPERATE ATTACHMENT
- LONG-TERM STORAGE
- MAINTENANCE OF ADDITIONAL FILTER FOR BREAKER
- SPECIFICATIONS
- CHANGE CONTROL PATTERN (MACHINE WITH CONTROL PATTERN CHANGE-OVER VALVE)
- CONTROL PATTERNS OTHER THAN STANDARD CONTROL PATTERN
- ATTACHMENTS AND OPTIONS
- TRACK SHOES SELECTION
- HANDLE RUBBER PAD SHOES AND ROAD LINERS
- RECOMMENDED ATTACHMENT OPERATIONS
- KomVision
- PRECAUTIONS WHEN USING KomVision
- MACHINE MONITOR EQUIPMENT NAME
- MACHINE MONITOR EQUIPMENT
- WARNING DISPLAY
- CAUTION LAMP LIST
- CAMERA SYSTEM CAUTION LAMP
- CAMERA CONTROLLER CAUTION LAMP
- MONITOR DISPLAY
- MONITOR DISPLAY SELECTOR SWITCH
- CAMERA IMAGE SELECTOR SWITCH
- KEY-ON CAMERA POSITION
- METHOD FOR CHECKING BEFORE STARTING
- METHOD FOR CHECKING CAMERA VISIBILITY
- TROUBLES AND ACTIONS
- REPLACEMENT PARTS
- DEFINED LIFE PARTS
- CONSUMABLE PARTS
- RECOMMENDED FUEL, COOLANT, AND LUBRICANT
- LUBRICATION CHART
- METHOD FOR USING FUEL, COOLANT AND LUBRICANTS ACCORDING TO AMBIENT TEMPERATURE
- RECOMMENDED BRANDS AND QUALITIES OTHER THAN KOMATSU GENUINE OILS
- INDEX
Link Belt
