Description

Komatsu PC16R-3HS Hydraulic Excavator Operation and Maintenance Manual (WENAM00650)

Komatsu PC16R-3HS Hydraulic Excavator Index:

• FOREWORD
  • CONTENTS
  • FOREWORD
  • KOMATSU MACHINE OPERATOR PRIVACY POLICY
  • SAFETY INFORMATION
  • NOISE EMISSION LEVELS
  • VIBRATION LEVEL
  • INTRODUCTION
  • MACHINE INFORMATION
    • LOCATION OF PRODUCT IDENTIFICATION NUMBER (PIN) AND MACHINE SERIAL NO. PLATE
    • LOCATION OF ENGINE NUMBER
    • SERVICE METER LOCATION
    • YOUR MACHINE SERIAL NUMBERS AND DISTRIBUTOR
    • SERIAL PLATE
    • DECLARATION OF CONFORMITY
  • ABBREVIATION LIST
• SAFETY
  • SAFETY LABELS
    • OTHER LABELS
  • GENERAL PRECAUTIONS COMMON TO OPERATION AND MAINTENANCE
    • PRECAUTIONS BEFORE STARTING OPERATION
    • PREPARATIONS FOR SAFE OPERATION
    • ACTIONS IF FIRE OCCURS
    • PRECAUTIONS TO PREVENT FIRE
    • PRECAUTIONS WHEN YOU GET ON OR OFF MACHINE
    • PRECAUTIONS FOR MACHINE AND JOBSITE
  • PRECAUTIONS FOR OPERATION
    • PRECAUTIONS FOR JOBSITE
    • START ENGINE
    • PRECAUTIONS FOR OPERATION
    • PRECAUTIONS FOR TRANSPORTATION
    • TOWING AND BEING TOWED
    • LIFTING OPERATION BY BUCKET WITH HOOK
  • PRECAUTIONS FOR MAINTENANCE
    • PRECAUTIONS BEFORE YOU START INSPECTION AND MAINTENANCE
    • PRECAUTIONS FOR CHECK AND MAINTENANCE
• OPERATION
  • GENERAL VIEW
    • MACHINE EQUIPMENT NAME
    • CONTROLS AND GAUGES NAMES
    • MACHINE MONITOR EQUIPMENT NAME
  • EXPLANATION OF COMPONENTS
    • MACHINE MONITOR EQUIPMENT
    • NAMES OF SWITCH PANEL EQUIPMENT
    • NAMES OF CONTROL LEVERS AND PEDALS
    • OTHER EQUIPMENT
    • KOMTRAX
  • MACHINE OPERATIONS AND CONTROLS
    • CHECKS AND ADJUSTMENT BEFORE YOU START ENGINE
    • OPERATIONS AND CHECKS BEFORE YOU START ENGINE
    • START ENGINE
    • OPERATIONS AND CHECKS AFTER YOU START ENGINE
    • STOP ENGINE
    • START MACHINE (TRAVEL FORWARD AND REVERSE) AND STOP MACHINE
    • STOP MACHINE
    • STEER MACHINE
    • SWING MACHINE
    • OPERATE WORK EQUIPMENT
    • OPERATE VARIABLE GAUGE
    • PROHIBITED OPERATIONS
    • WORK PRECAUTIONS
    • PRECAUTIONS WHEN YOU WORK ON SLOPE
    • ESCAPE FROM SOFT GROUND
    • RECOMMENDED APPLICATIONS
    • REPLACE BUCKET
    • PARK MACHINE
    • CHECK AFTER YOU FINISH WORK
    • LOCK
  • HEATER
    • AIR FLOW SELECTOR SWITCH
    • TEMPERATURE CONTROL SWITCH
    • VENT
    • HOT WATER FLOW REGULATOR VALVE
  • HANDLE RUBBER SHOES
    • RUBBER SHOES
  • TRANSPORTATION
    • LOAD AND UNLOAD A TRAILER
    • LIFT MACHINE
  • COLD WEATHER OPERATION
    • COLD WEATHER INFORMATION
    • FUEL AND LUBRICANTS
    • COOLANT
    • BATTERY
    • PRECAUTIONS AFTER DAILY WORK COMPLETION IN COLD WEATHER
    • AFTER COLD WEATHER SEASON
  • LONG-TERM STORAGE PRECAUTIONS
    • PREPARATION FOR LONG-TERM STORAGE
    • MAINTENANCE DURING LONG-TERM STORAGE
    • START MACHINE AFTER LONG-TERM STORAGE
  • TROUBLES AND ACTIONS
    • ACTIONS WHEN YOU RUN OUT OF FUEL
    • PHENOMENA THAT ARE NOT FAILURES
    • PRECAUTIONS FOR TOWING MACHINE
    • PRECAUTIONS FOR SEVERE JOB CONDITION
    • ACTIONS WHEN BATTERY IS DISCHARGED
    • OTHER TROUBLE
• MAINTENANCE
  • PRECAUTIONS FOR MAINTENANCE
  • MAINTENANCE INFORMATION
    • OIL, FUEL, AND COOLANT
    • ELECTRICAL COMPONENTS
    • HYDRAULIC COMPONENTS
    • STANDARD TORQUE
  • MAINTENANCE SCHEDULE
    • MAINTENANCE INTERVAL TABLE
    • MAINTENANCE INTERVAL FOR HYDRAULIC BREAKER
  • MAINTENANCE PROCEDURE
    • INITIAL 10 HOURS MAINTENANCE
    • WHEN REQUIRED
    • CHECK BEFORE YOU START OPERATION
    • EVERY 100 HOURS MAINTENANCE
    • EVERY 500 HOURS MAINTENANCE
    • EVERY 1000 HOURS MAINTENANCE
    • EVERY 2000 HOURS MAINTENANCE
    • EVERY 4000 HOURS MAINTENANCE
  • END OF SERVICE LIFE
• SPECIFICATIONS
  • SPECIFICATIONS
  • EXPLANATION OF LIFT CAPACITY
• ATTACHMENTS AND OPTIONS
  • PRECAUTIONS TO USE ATTACHMENTS AND OPTIONS SAFELY
  • QUICK COUPLER SYSTEM
    • HANDLE QUICK COUPLER
  • HANDLE BUCKET WITH HOOK
    • WORK PRECAUTIONS
  • HANDLE MACHINE READY FOR INSTALLATION OF ATTACHMENT (WITH CONTROL PEDAL)
    • EXPLANATION OF COMPONENTS ON MACHINES WITH ATTACHMENT
    • CONNECT HYDRAULIC CIRCUIT OF MACHINES READY FOR INSTALLATION OF ATTACHMENT
    • CHANGE OVER HYDRAULIC CIRCUIT OF MACHINES WITH ATTACHMENT
    • OPERATE ATTACHMENT
    • LONG-TERM STORAGE
    • SPECIFICATIONS
  • HANDLE MACHINE READY FOR INSTALLATION OF ATTACHMENT (WITH PROPORTIONAL CONTROL LEVER)
    • EXPLANATION OF COMPONENTS ON MACHINES WITH ATTACHMENT
    • CONNECT HYDRAULIC CIRCUIT OF ATTACHMENT (1st LINE)
    • CONNECT HYDRAULIC CIRCUIT OF ATTACHMENT (2nd/3rd LINE)
    • CHANGE OVER HYDRAULIC CIRCUIT OF MACHINES WITH ATTACHMENT
    • OPERATE ATTACHMENT ON MACHINE WITH PROPORTIONAL CONTROL LEVER
  • ARM/PIN INFORMATION
  • ATTACHMENTS AND OPTIONS
    • INSTALL ATTACHMENT
  • RECOMMENDED ATTACHMENT OPERATIONS
    • HYDRAULIC BREAKER
• REPLACEMENT PARTS
  • DEFINED LIFE PARTS
    • DEFINED LIFE PARTS LIST
  • CONSUMABLE PARTS
    • CONSUMABLE PARTS LIST
  • RECOMMENDED FUEL, COOLANT, AND LUBRICANT
    • LUBRICATION CHART
    • USE FUEL, COOLANT AND LUBRICANTS ACCORDING TO AMBIENT TEMPERATURE
    • RECOMMENDED BRANDS AND QUALITIES OTHER THAN KOMATSU GENUINE OILS
• INDEX

Link Belt