Komatsu PC210LCi-11E0 Hydraulic Excavator Index:

• FOREWORD
  • CONTENTS
  • READ THIS MANUAL
  • KOMATSU MACHINE OPERATOR PRIVACY POLICY
  • SAFETY INFORMATION
  • INTRODUCTION
    • intelligent Machine Control
    • MAIN USE OF MACHINE
    • DEMOLITION WORK
  • ABBREVIATION LIST
  • DECLARATION OF CONFORMITY (KUK MANUFACTURE)
  • DECLARATION OF CONFORMITY (KLTD MANUFACTURE)
• SAFETY
  • SAFETY LABELS
    • LOCATION OF SAFETY LABELS
    • SAFETY LABELS
  • PRECAUTIONS FOR OPERATION
    • START ENGINE
    • PRECAUTIONS RELATED TO CONTROL BOX
    • PRECAUTIONS RELATED TO SEMI-AUTO MODE
    • PRECAUTIONS FOR TRANSPORTATION
• OPERATION
  • GENERAL VIEW
    • MACHINE EQUIPMENT NAME
    • CAB EQUIPMENT NAMES
  • EXPLANATION OF COMPONENTS
    • EXPLANATION OF MACHINE MONITOR EQUIPMENT
    • SWITCH
    • CONTROL LEVERS AND PEDALS
    • intelligent Machine Control SYSTEM
    • OTHER EQUIPMENT
  • MACHINE OPERATIONS AND CONTROLS
    • CHECKS AND ADJUSTMENT BEFORE STARTING ENGINE
    • START ENGINE
    • HANDLING QUICK COUPLER PIN GRAB
    • METHOD FOR STOPPING ENGINE
    • PROHIBITED OPERATIONS
    • PARK MACHINE
  • HANDLING RADIO
  • TRANSPORTATION
    • REMOVE AND INSTALL GNSS ANTENNA
    • REMOVE AND INSTALL HANDRAIL
    • REMOVE AND INSTALL GNSS RADIO DEVICE ANTENNA AND ANTENNA FOR NETWORK MODEM
  • PRECAUTIONS FOR LONG-TERM STORAGE
    • STARTING MACHINE AFTER LONG-TERM STORAGE
  • TROUBLES AND ACTIONS
    • IF ERROR INFORMATION IS DISPLAYED ON CONTROL BOX
    • OTHER TROUBLE
• MAINTENANCE
  • MAINTENANCE SCHEDULE
    • MAINTENANCE SCHEDULE TABLE
  • MAINTENANCE PROCEDURE
    • EVERY 500 HOURS MAINTENANCE
• SPECIFICATIONS
  • SPECIFICATIONS
    • SPECIFICATIONS:PC210LCI-11E0
• ATTACHMENTS AND OPTIONS
  • PRECAUTIONS FOR USING ATTACHMENT AND OPTIONS
    • PRECAUTIONS WHEN SELECTING
    • READ THE OPERATION AND MAINTENANCE MANUAL THOROUGHLY
    • PRECAUTIONS WHEN REMOVING AND INSTALLING
    • PRECAUTIONS FOR USING
  • ATTACHMENTS AND OPTIONS
    • AUTO TILT BUCKET
  • RECOMMENDED ATTACHMENT OPERATIONS
    • HYDRAULIC BREAKER
• SETTING
  • INTELLIGENT MACHINE CONTROL SETTINGS
  • CONTROL BOX
    • METHOD FOR DISPLAYING MAIN MENU
  • MACHINE MONITOR
    • MACHINE SETTINGS
    • MC SETTING
• EXECUTIONS
  • SEMI-AUTO MODE
    • PRECAUTIONS FOR OPERATION
    • PRECAUTIONS FOR REPLACING PARTS AND FAILURES
    • WORKING MODE
    • WORKING MODE (WHEN AUTO TILT BUCKET IS EQUIPPED)
    • SEMI-AUTO MODE SETTINGS
  • TRAVEL MODE
    • TRAVEL MODE SETTINGS
    • DISPLAY OF TRAVEL MODE
    • OFFSET MENU OF SURFACE
    • TARGET SURFACE SETTINGS
  • ROUGH DIGGING MODE
    • METHOD FOR SETTING ROUGH DIGGING SCREEN
    • TEMPORARY DESIGN MENU
  • FINE DIGGING MODE
    • METHOD FOR SETTING FINE DIGGING MODE SCREEN
  • TARGET SURFACE SETTINGS
    • TARGET SURFACE SETTING MENU
    • METHOD FOR SETTING TARGET SURFACE
  • BUCKET EDGE POSITION
    • DISPLAY BUCKET EDGE POSITION
    • METHOD FOR COMPARING WITH BENCHMARK
    • METHOD FOR CORRECTING BUCKET EDGE POSITION
  • DAILY CALIBRATION
    • WALK-AROUND CHECKS OF INTELLIGENT MACHINE CONTROL EQUIPMENT
  • CHECK GNSS COMMUNICATION STATUS
    • METHOD FOR CHECKING GNSS COMMUNICATION STATUS
    • METHOD FOR CHECKING NUMBER OF SATELLITES AND ERROR OF POSITIONING
    • METHOD FOR DISPLAYING BUCKET EDGE COORDINATES
    • METHOD FOR SETTING SATELLITE POSITION DISPLAY AND ELEVATION ANGLE
    • METHOD FOR DISPLAYING GNSS RECEIVER INFORMATION
    • METHOD FOR CHEKING EXPECTANCY OF EDGE ACCURANCY
    • METHOD FOR SETTING GLONASS SATELLITE
    • SET SATELLITE
    • METHOD FOR SETTING TILT SENSOR MODE
  • USE OF TOPO SURVEY
    • METHOD FOR PERFORMING TOPO SURVEY MANUALLY
    • METHOD FOR PERFORMING AUTO-TOPO SURVEY
    • METHOD FOR CANCELING TOPOGRAPHIC SURVEYS
  • TROUBLESHOOTING
    • CONTROL BOX SCREEN DISPLAY
    • SEMI-AUTO MODE
    • WORKING ACCURACY
    • AUTO TILT BUCKET
• INDEX
• Blank Page