Komatsu PC228USLC-10 Hydraulic Excavator Index:

• FOREWORD
  • FOREWORD
  • SAFETY INFORMATION
    • NOISE EMISSION LEVELS
    • VIBRATION LEVELS
    • GUIDE TO REDUCE VIBRATION LEVELS ON MACHINE
  • INTRODUCTION
    • USE OF MACHINE
    • DEMOLITION WORK
    • DIRECTIONS OF MACHINE
    • VISIBILITY FROM OPERATOR’S SEAT
    • STRUCTURE TO PROTECT THE OPERATOR
  • PRODUCT INFORMATION
    • PRODUCT IDENTIFICATION NUMBER (PIN)／MACHINE SERIAL NO. PLATE
    • EPA REGULATIONS, ENGINE NUMBER PLATE
    • Fluorinated Greenhouse Gases
    • SERVICE METER LOCATION
    • YOUR MACHINE SERIAL NUMBERS AND DISTRIBUTOR
    • SERIAL PLATE
    • Declaration of conformity (Directive 2006/42/EC)
• SAFETY
  • SAFETY
  • SAFETY LABELS
    • LOCATION OF SAFETY LABELS
    • SAFETY LABELS
  • GENERAL PRECAUTIONS COMMON TO OPERATION AND MAINTENANCE
    • PRECAUTIONS BEFORE STARTING OPERATION
    • PREPARATIONS FOR SAFE OPERATION
    • FIRE PREVENTION
    • PRECAUTIONS WHEN GETTING ON OR OFF MACHINE
    • DO NOT GET CAUGHT IN WORK EQUIPMENT
    • PRECAUTIONS RELATED TO PROTECTIVE STRUCTURES
    • PROTECTION AGAINST FALLING, FLYING, OR INTRUDING OBJECTS
    • ACTIONS IN THE EVENT OF DAMAGE TO SAFETY STRUCTURES
    • UNAUTHORIZED MODIFICATION
    • PRECAUTIONS RELATED TO ATTACHMENTS AND OPTIONS
    • PRECAUTIONS RELATED TO CAB GLASS
    • PRECAUTIONS WHEN RUNNING ENGINE INSIDE BUILDING
  • PRECAUTIONS FOR OPERATION
    • PRECAUTIONS FOR JOBSITE
    • STARTING ENGINE
    • OPERATION
    • TRANSPORTATION
    • TOWING
    • LIFTING OBJECTS WITH BUCKETS
  • PRECAUTIONS FOR MAINTENANCE
    • PRECAUTIONS BEFORE STARTING INSPECTION AND MAINTENANCE
    • PRECAUTIONS FOR INSPECTION AND MAINTENANCE
• OPERATION
  • GENERAL VIEW
    • GENERAL VIEW OF MACHINE
    • GENERAL VIEW OF CONTROLS AND GAUGES
  • EXPLANATION OF COMPONENTS
    • MACHINE MONITOR
    • SWITCHES
    • CONTROL LEVERS AND PEDALS
    • CEILING WINDOW
    • OPEN AND CLOSE CAB FRONT WINDOW
    • SLIDE DOOR
    • EMERGENCY ESCAPE HAMMER
    • OPEN AND CLOSE ENGINE HOOD
    • PUMP ROOM DOOR, BATTERY ROOM DOOR
    • VALVE ROOM DOOR
    • CAPS AND COVERS WITH LOCK
    • MAGAZINE BOX
    • CUP HOLDER
    • ASHTRAY
    • HANDLING AIR CONDITIONER
    • HANDLING RADIO
    • AUXILIARY ELECTRIC POWER
    • FUSE
    • FUSIBLE LINK
    • TOOLBOX
    • GREASE PUMP HOLDER
    • REFUELLING PUMP
    • FIRE EXTINGUISHER
    • BATTERY DISCONNECT SWITCH
    • SYSTEM OPERATING LAMP
    • HANDLING Komatsu Diesel Particulate Filter (KDPF)
    • HANDLING Komatsu Closed Crankcase Ventilation (KCCV)
    • HANDLING MACHINES EQUIPPED WITH KOMTRAX
  • MACHINE OPERATIONS AND CONTROLS
    • CHECKS AND ADJUSTMENT BEFORE STARTING ENGINE
    • STARTING ENGINE
    • OPERATIONS AND CHECKS AFTER STARTING ENGINE
    • STOPPING ENGINE
    • MACHINE OPERATION
    • STEERING MACHINE
    • SWINGING MACHINE
    • WORK EQUIPMENT CONTROLS AND OPERATIONS
    • WORKING MODE
    • PROHIBITED OPERATIONS
    • RULES FOR OPERATION
    • TRAVELLING ON SLOPES
    • ESCAPE FROM MUD
    • RECOMMENDED APPLICATIONS
    • REPLACING AND INVERTING BUCKET
    • PARKING MACHINE
    • AFTER DAILY WORK COMPLETION
    • LOCKING
  • TRANSPORTATION
    • TRANSPORTATION PROCEDURE
    • LOADING AND UNLOADING WITH TRAILER
    • LIFTING MACHINE
  • COLD WEATHER OPERATION
    • COLD WEATHER OPERATION INFORMATION
    • AFTER DAILY WORK COMPLETION
    • AFTER COLD WEATHER SEASON
  • LONG-TERM STORAGE
    • BEFORE STORAGE
    • DURING STORAGE
    • AFTER STORAGE
    • STARTING MACHINE AFTER LONG-TERM STORAGE
  • TROUBLES AND ACTIONS
    • RUNNING OUT OF FUEL
    • PHENOMENA THAT ARE NOT FAILURES
    • TOWING MACHINE
    • LIGHTWEIGHT TOWING HOLE
    • SEVERE JOB CONDITION
    • DISCHARGED BATTERY
    • OTHER TROUBLE
• MAINTENANCE
  • RULES FOR MAINTENANCE
    • SERVICE METER READING
    • KOMATSU GENUINE REPLACEMENT PARTS
    • KOMATSU GENUINE LUBRICANTS
    • ALWAYS USE CLEAN WASHER FLUID
    • FRESH AND CLEAN LUBRICANTS
    • CHECK DRAINED OIL AND USED FILTER
    • CAUTION FOR REFILLING OIL OR FUEL
    • WELDING INSTRUCTIONS
    • DO NOT DROP THINGS INSIDE MACHINE
    • DUSTY JOBSITES
    • AVOID MIXING OIL
    • LOCKING INSPECTION COVERS
    • BLEED AIR FROM HYDRAULIC CIRCUIT
    • PRECAUTIONS WHEN INSTALLING HYDRAULIC HOSES
    • CHECKS AFTER INSPECTION AND MAINTENANCE
    • FUEL AND LUBRICANTS TO MATCH THE AMBIENT TEMPERATURE
    • CLOSE ENGINE HOOD SECURELY
  • OUTLINE OF SERVICE
    • HANDLING OIL, FUEL, COOLANT, AND PERFORMING OIL CLINIC
    • HANDLING ELECTRICAL COMPONENTS
  • STANDARD TIGHTENING TORQUE FOR BOLTS AND NUTS
    • TIGHTENING TORQUE LIST
  • MAINTENANCE SCHEDULE
    • MAINTENANCE SCHEDULE TABLE
    • MAINTENANCE INTERVAL FOR HYDRAULIC BREAKER
  • MAINTENANCE PROCEDURE
    • INITIAL 250 HOURS MAINTENANCE (ONLY AFTER THE FIRST 250 HOURS)
    • WHEN REQUIRED
    • CHECKS BEFORE STARTING
    • EVERY 100 HOURS MAINTENANCE
    • EVERY 250 HOURS MAINTENANCE
    • EVERY 500 HOURS MAINTENANCE
    • EVERY 1000 HOURS MAINTENANCE
    • EVERY 2000 HOURS MAINTENANCE
    • EVERY 4000 HOURS MAINTENANCE
    • EVERY 4500 HOURS MAINTENANCE
    • EVERY 5000 HOURS MAINTENANCE
    • EVERY 8000 HOURS MAINTENANCE
  • END OF SERVICE LIFE
• SPECIFICATIONS
  • SPECIFICATIONS 1-piece boom
    • EXPLANATION OF LIFTING CAPACITY CHART 1-piece boom
  • SPECIFICATIONS 2-piece boom
    • EXPLANATION OF LIFTING CAPACITY CHART 2-piece boom
• ATTACHMENTS AND OPTIONS
  • GENERAL PRECAUTIONS FOR SAFETY
    • PRECAUTIONS WHEN SELECTING
    • READ THE OPERATION AND MAINTENANCE MANUAL THOROUGHLY
    • PRECAUTIONS WHEN REMOVING OR INSTALLING
  • PRECAUTIONS WHEN USING
  • HANDLING QUICK COUPLER
  • BUCKET WITH HOOK
    • HOOK CONDITION
    • PROHIBITED OPERATIONS
  • MACHINE READY FOR INSTALLATION OF ATTACHMENT
    • EXPLANATION OF COMPONENTS
    • ATTACHMENT 1 CONTROL
    • HYDRAULIC CIRCUIT
    • ATTACHMENT REMOVAL AND INSTALLATION
    • OPERATION
    • Operation when using attachment 2
    • LONG-TERM STORAGE
    • SPECIFICATIONS
  • ATTACHMENTS AND OPTIONS
    • ATTACHMENT COMBINATIONS
    • TRACK SHOES SELECTION
    • BUCKET TEETH SELECTION
    • HANDLING ROAD LINERS
  • RECOMMENDED ATTACHMENT OPERATIONS
    • HYDRAULIC BREAKER
  • 2-Piece Boom
    • WORK EQUIPMENT CONTROLS AND OPERATIONS
    • WORK POSSIBLE USING 2-PIECE BOOM
    • Every 100 hours maintenance
    • Every 500 hours maintenance
    • bucket combinations
• REPLACEMENT PARTS
  • SAFETY CRITICAL PARTS
    • SAFETY CRITICAL PARTS LIST
  • CONSUMABLE PARTS
    • CONSUMABLE PARTS LIST
  • RECOMMENDED FUEL, COOLANT, AND LUBRICANT
    • LUBRICATION CHART
    • USE OF FUEL, COOLANT AND LUBRICANTS ACCORDING TO AMBIENT TEMPERATURE
    • RECOMMENDED BRANDS AND QUALITY FOR PRODUCTS OTHER THAN KOMATSU GENUINE OIL
• INDEX