Komatsu WA250PT-5H Wheel Loader Index:

• FOREWORD
  • Foreword
  • Safety information
  • Introduction
    • Intended use
    • Directions of machine
  • Necessary information
    • Machine serial No. plate and position
    • Engine serial No. plate and position
    • ROPS/FOPS-Cab serial no. plate
    • Axle serial no. plate
    • Transmission serial no. plate
    • Seat operator serial no. plate
    • Position of service meter
    • Table to enter serial No. and distributor
  • Contents
  • Dimensions, weights and operating data
    • WA250PT-5H: Dimensions, weights and operating data
  • CE-conforming equipment
    • CE-conforming equipment
    • Manufacturer-supplied CE-conforming equipment, according to document 421-93-H1900
• SAFETY
  • Safety labels
    • Location of safety labels
    • Presentation of safety labels
  • General precautions
    • Safety rules
  • Precautions for operation
    • Starting engine
    • Operation
    • Transportation
    • Battery
    • Towing
  • Precautions for maintenance
    • Safety instructions
  • Precautions with tires
    • Handling tires
    • Precautions when storing tires
• OPERATION
  • General view
    • General view of machine
    • General view of controls and gauges
  • Explanation of components
    • Machine monitor
    • Switches
    • Control levers, pedals
    • Steering tilt lock lever
    • Cap and cover with lock
    • Safety bar
    • Towing pin
    • Grease pump
    • Cab door inner lock
    • Cab door open lock
    • Cab window open lock cancel knob
    • Fuse
    • Slow blow fuse
    • Power outlet
    • Air conditioner
    • Handling cab wiper
  • Operation
    • Check before starting engine, adjust
    • Starting engine
    • Operations and checks after starting engine
    • Stopping engine
    • Moving the machine (Directional, speed), stopping the machine
    • Turning
    • Operation of work equipment
    • Handling hydraulic quick coupler
    • Work possible using wheel loader
    • Precautions for operation
    • Adjusting work equipment posture
    • Parking machine
    • Check after stopping engine
    • Checks after completion of operation
    • Locking
    • Handling the tires
  • Transportation
    • Transportation procedure
    • Loading, unloading work with trailers
    • Lifting machine
  • Cold weather operation
    • Precautions for low temperature
    • Precautions after completion of work
    • After cold weather
    • Warming-up operation for steering hydraulic circuit in cold weather
  • Long-term storage
    • Before storage
    • During storage
    • After storage
  • Troubleshooting
    • When machine runs out of fuel
    • Towing the machine
    • If battery is discharged
    • Other trouble
• MAINTENANCE
  • Guides to maintenance
  • Outlines of service
    • Handling oil, fuel, coolant, grease and performing oil clinic
    • Outline of electric system
  • Wear parts
    • Wear parts list
  • Fuel, coolant and lubricants
    • Lubrication chart
    • acea e5Proper selection of fuel, coolant and lubricants
  • Standard tightening torques for bolts and nuts
    • Torque list
  • Periodic replacement of safety critical parts
    • Safety critical parts
  • Maintenance schedule chart
    • Service schedule
  • Service procedure
    • Initial 50 hours service (only after the first 50 hours)
    • Initial 250 hours service (only after the first 250 hours)
    • When required
    • Check before starting
    • Every 50 hours service
    • Every 100 hours service
    • Every 250 hours service
    • Every 500 hours service
    • Every 1000 hours service
    • Every 2000 hours service
    • Every 4000 hours service
• TECHNICAL DATA
  • Technical data
  • Noise emission levels
  • Vibration levels
    • Operating condition:
    • Guide to Reduce Vibration Levels on Machine
• ATTACHMENTS, OPTIONS
  • Selecting bucket and tires
  • Handling fork tool
    • Explanation of components
    • Operation
  • Method of using 3 levers
    • Explanation of components
    • Operation
  • Central lubrication system
    • Operating the central lubrication system
    • Display and control unit
    • Changing the lubrication interval times
• INDEX
  • Index
• NOTES
  • NOTES