Komatsu WA70M-8E0 Wheel Loader Operation and Maintenance Manual (VENAM09002)

Komatsu WA70M-8E0 Wheel Loader Operation and Maintenance Manual (VENAM09002)

Komatsu WA70M-8E0 Wheel Loader Index:

• FOREWORD
  • CONTENTS
  • READ THIS MANUAL
  • EU DIRECTIVES
  • KOMATSU MACHINE OPERATOR PRIVACY POLICY
  • SAFETY INFORMATION
  • SAFETY LABELS
  • NOISE EMISSION LEVELS
  • VIBRATION LEVEL
  • INTRODUCTION
  • ENGINE TECHNOLOGY TO CONFORM EXHAUST GAS EMISSION
  • MACHINE INFORMATION
    • LOCATION OF PRODUCT IDENTIFICATION NUMBER (PIN) AND MACHINE SERIAL NO. PLATE
    • LOCATION OF ENGINE NUMBER PLATE
    • ROPS/FOPS SERIAL PLATE LOCATION
    • AXLE SERIAL PLATE LOCATION
    • SEAT PLATE LOCATION
    • FLUORINATED GREENHOUSE GASES
    • SERVICE METER LOCATION
  • YOUR MACHINE SERIAL NUMBERS AND DISTRIBUTOR
  • SERIAL PLATE
  • ALTERNATIVE SERIAL PLATE
  • DECLARATION OF CONFORMITY
  • RETROFITTING BY THIRD-PARTY SUPPLIERS
  • ABBREVIATION LIST
• SAFETY
  • SAFETY LABELS
  • GENERAL PRECAUTIONS COMMON TO OPERATION AND MAINTENANCE
    • PRECAUTIONS BEFORE STARTING OPERATION
    • PREPARATIONS FOR SAFE OPERATION
    • ACTIONS IF FIRE OCCURS
    • PRECAUTIONS TO PREVENT FIRE
    • PRECAUTIONS WHEN YOU GET ON OR OFF MACHINE
    • PRECAUTIONS FOR MACHINE AND JOBSITE
  • PRECAUTIONS FOR OPERATION
    • PRECAUTIONS FOR JOBSITE
    • START ENGINE
    • PRECAUTIONS FOR OPERATION
    • PRECAUTIONS FOR TRANSPORTATION
    • TOWING AND BEING TOWED
  • PRECAUTIONS FOR MAINTENANCE
    • PRECAUTIONS BEFORE YOU START INSPECTION AND MAINTENANCE
    • PRECAUTIONS FOR CHECK AND MAINTENANCE
  • PRECAUTIONS FOR TIRE
• OPERATION
  • GENERAL VIEW
    • MACHINE EQUIPMENT NAME
    • CONTROLS AND GAUGES NAMES
    • SWITCH PANEL EQUIPMENT NAME
    • MACHINE MONITOR EQUIPMENT NAME
    • NAMES OF OTHER EQUIPMENT
  • EXPLANATION OF COMPONENTS
    • MACHINE MONITOR EQUIPMENT
    • NAMES OF SWITCH PANEL EQUIPMENT
    • NAMES OF CONTROL LEVERS AND PEDALS
    • OTHER EQUIPMENT
  • MACHINE OPERATIONS AND CONTROLS
    • CHECKS AND ADJUSTMENT BEFORE YOU START ENGINE
    • START ENGINE
    • OPERATIONS AND CHECKS AFTER YOU START ENGINE
    • STOP ENGINE
    • START AND STOP MACHINE
    • STEER MACHINE
    • OPERATE WORK EQUIPMENT
    • WORK PRECAUTIONS
    • RECOMMENDED APPLICATIONS
    • PARK MACHINE
    • CHECK AFTER YOU FINISH WORK
    • LOCK
  • TIRES
    • TIRE PRESSURE
    • PRECAUTIONS FOR LOAD-AND-CARRY OPERATION
  • AIR CONDITIONER
    • SET THE VENTILATION AND HEATING SYSTEM
    • SET THE AIR CONDITIONER
  • TRANSPORTATION
    • LOAD AND UNLOAD A TRAILER
    • LIFT MACHINE PRECAUTIONS
  • COLD WEATHER OPERATION
    • COLD WEATHER INFORMATION
    • FUEL AND LUBRICANTS
    • COOLANT
    • BATTERY
    • PRECAUTIONS AFTER DAILY WORK COMPLETION IN COLD WEATHER
    • PRECAUTIONS IN COLD WEATHER
    • AFTER COLD WEATHER SEASON
  • LONG-TERM STORAGE PRECAUTIONS
    • PREPARATION FOR LONG-TERM STORAGE
    • MAINTENANCE DURING LONG-TERM STORAGE
    • START MACHINE AFTER LONG-TERM STORAGE
  • TROUBLES AND ACTIONS
    • ACTIONS WHEN YOU RUN OUT OF FUEL
    • CHECK THE SERVICE BRAKE
    • CHECK PARKING BRAKE
    • EMERGENCY STEERING PROPERTIES
    • EMERGENCY LOWERING
    • PRECAUTIONS FOR TOWING MACHINE
    • DISCHARGED BATTERY PRECAUTIONS
    • PRECAUTIONS WHEN YOU CHARGE BATTERY
    • START ENGINE WITH JUMPER CABLES
    • OTHER TROUBLE
• MAINTENANCE
  • PRECAUTIONS FOR MAINTENANCE
  • MAINTENANCE GUIDE
    • TIP UP THE OPERATOR’S CAB (STANDARD, WITHOUT TIPPING CYLINDER)
    • TIP DOWN THE OPERATOR’S CAB (STANDARD, WITHOUT TIPPING CYLINDER)
    • TIP UP THE OPERATOR’S CAB (OPTION, WITH TIPPING CYLINDER)
    • TIP DOWN THE OPERATOR’S CAB (OPTION, WITH TIPPING CYLINDER)
  • MAINTENANCE INFORMATION
    • OIL, FUEL, AND COOLANT
    • BATTERY TERMINAL
    • ELECTRICAL COMPONENTS
  • STANDARD TORQUE
  • MAINTENANCE SCHEDULE
    • PERIODIC MAINTENANCE FOR ENGINE
    • MAINTENANCE INTERVAL TABLE
  • MAINTENANCE PROCEDURE
    • INITIAL 10 HOURS MAINTENANCE (ONLY FOR THE FIRST 100 HOURS)
    • WHEN REQUIRED
    • CHECK BEFORE YOU START OPERATION
    • INITIAL 50 HOURS MAINTENANCE (ONLY AFTER THE FIRST 50 HOURS)
    • INITIAL 500 HOURS MAINTENANCE (ONLY AFTER THE FIRST 500 HOURS)
    • EVERY 10 HOURS MAINTENANCE
    • EVERY 50 HOURS MAINTENANCE
    • EVERY 250 HOURS MAINTENANCE
    • EVERY 500 HOURS MAINTENANCE
    • EVERY 1000 HOURS MAINTENANCE
    • EVERY 1500 HOURS MAINTENANCE
    • EVERY 2000 HOURS MAINTENANCE
    • EVERY 3000 HOURS MAINTENANCE
    • EVERY 4000 HOURS MAINTENANCE
    • EVERY 6000 HOURS MAINTENANCE
    • EVERY 8000 HOURS MAINTENANCE
    • END OF SERVICE LIFE
• SPECIFICATIONS
  • SPECIFICATIONS WA70M-8E0
• ATTACHMENTS AND OPTIONS
  • CENTRAL LUBRICATION SYSTEM
    • CHANGE LUBRICATION INTERVAL SYSTEM
    • OPERATE LUBRICATION SYSTEM
    • DISPLAY AND OPERATING UNIT
    • INITIAL 10 HOURS MAINTENANCE (ONLY FOR THE FIRST 100 HOURS)
    • CHECK AUTO-GREASING AND FILL GREASE
  • ECSS
    • OPERATE THE ECSS
  • RETURN TO DIG
  • REVERSIBLE FAN
    • CLEAN RADIATOR FINS
  • AIR CONDITIONER
  • TOWING PIN
  • SPEED CONTROL
  • ROAD HOMOLOGATION (FOR ITALY)
• REPLACEMENT PARTS
  • DEFINED LIFE PARTS
    • DEFINED LIFE PARTS LIST
  • CONSUMABLE PARTS
    • CONSUMABLE PARTS LIST
  • RECOMMENDED FUEL, COOLANT, AND LUBRICANT
    • LUBRICATION CHART
    • USE FUEL, COOLANT AND LUBRICANTS ACCORDING TO AMBIENT TEMPERATURE
    • RECOMMENDED BRANDS AND QUALITIES OTHER THAN KOMATSU GENUINE OILS
• INDEX

Link Belt