Komatsu WB93S-5E0 Backhoe Loader Index:

• 1.1 FOREWORD
• 1.2 KOMATSU MACHINE OPERATOR PRIVACY POLICY
• 1.3 INFORMATION ON SAFETY
  • 1.3.1 POSITION OF THE NOISE PLATES ON MACHINES WITH CAB
  • 1.3.2 VIBRATIONS TO WHICH THE OPERATOR IS SUBJECTED
  • 1.3.3 GUIDE WHEN WORKING IN AREAS WHERE AIR POLLUTION
• 1.4 INTRODUCTION
  • 1.4.1 INTENDED USES
  • 1.4.2 DEMOLITION WORK
  • 1.4.3 IMPROPER OR UNAUTHORIZED USE
  • 1.4.4 MAIN CHARACTERISTICS
  • 1.4.5 RUNNING-IN
  • 1.4.6 POSITIONS AND DIRECTIONS OF THE MACHINE
    • 1.4.6.1 WHEN OPERATING THE LOADER OR TRAVELLING
    • 1.4.6.2 WHEN OPERATING THE BACKHOE
  • 1.4.7 VISIBILITY FROM OPERATOR’S SEAT
  • 1.4.8 PROTECTIVE STRUCTURES
• 1.5 PRODUCT IDENTIFICATION
  • 1.5.1 MACHINE IDENTIFICATION NUMBER (PIN)
  • 1.5.2 MACHINE IDENTIFICATION PLATE AND PRODUCT IDENTIFICATION NUMBER (PIN)
    • 1.5.2.1 MACHINE SERIAL NUMBER PLATE (according directive 2006/42/EC)
  • 1.5.3 ENGINE SERIAL NUMBER AND EXHAUST GAS EMISSION PLATE
  • 1.5.4 FRONT AXLE SERIAL NUMBER
  • 1.5.5 REAR AXLE SERIAL NUMBER
  • 1.5.6 TRANSMISSION SERIAL NUMBER
  • 1.5.7 CAB SERIAL NUMBER
  • 1.5.8 TABLE TO ENTER SERIAL NO. AND DISTRIBUTOR
  • 1.5.9 DECLARATION OF CONFORMITY
• 1.6 KOMTRAX SYSTEM
  • 1.6.1 GENERAL PRECAUTIONS
• TABLE OF CONTENTS
• 2.1 SAFETY, NOISE AND VIBRATION PLATES
  • 2.1.1 POSITION OF THE SAFETY PLATES
  • 2.1.2 PICTOGRAMS AND RELEVANT MEANINGS
• 2.2 GENERAL PRECAUTIONS
  • 2.2.1 GENERAL SAFETY RULES
  • 2.2.2 SAFETY DEVICES AND GUARDS
  • 2.2.3 CLOTHING AND PERSONAL PROTECTION ITEMS
  • 2.2.4 UNAUTHORIZED MODIFICATIONS
  • 2.2.5 LEAVING THE OPERATOR’S SEAT
  • 2.2.6 GETTING ON AND OFF THE MACHINE
  • 2.2.7 CHECKING THE REAR-VIEW MIRRORS
  • 2.2.8 PREVENTING FIRES DUE TO FUEL AND OIL
  • 2.2.9 LIFTING OF PERSONNEL PROHIBITED
  • 2.2.10 PREVENTING BURNS
  • 2.2.11 ASBESTOS DUST HAZARD PREVENTION
  • 2.2.12 PREVENTING DAMAGE CAUSED BY THE WORK EQUIPMENT
  • 2.2.13 DETERGENT FOR THE WINDOWS
  • 2.2.14 FIRE EXTINGUISHERS AND FIRST AID KIT
  • 2.2.15 FALLING OBJECTS, FLYING OBJECTS AND INTRUDING OBJECTS PREVENTION
  • 2.2.16 CAUTIONS RELATED TO ROPS
  • 2.2.17 PRECAUTIONS CONCERNING THE EQUIPMENT
• 2.3 PRECAUTIONS TO BE TAKEN BEFORE STARTING THE ENGINE
  • 2.3.1 SAFETY ON THE WORK SITE
  • 2.3.2 FIRE PREVENTION
  • 2.3.3 PRECAUTIONS TO BE TAKEN FOR THE OPERATOR’S CAB
  • 2.3.4 ROOM VENTILATION
  • 2.3.5 CLEANING WINDOWS, MIRRORS AND LIGHTS – CHECKING THE WINDSHIELD WIPER BLADES AND THE BULBS
• 2.4 PRECAUTIONS TO BE TAKEN DURING WORK
  • 2.4.1 WHEN STARTING THE ENGINE
  • 2.4.2 RULES FOR TRAVELLING ON ROADS
  • 2.4.3 REGULATIONS FOR ROAD TRANSFER (TUV approval)
  • 2.4.4 HAND SIGNALS
  • 2.4.5 CHECKS FOR TRAVELLING IN REVERSE
  • 2.4.6 MOVING THE MACHINE
  • 2.4.7 WORKING ON SLOPES
  • 2.4.8 PROHIBITED OPERATIONS
  • 2.4.9 PREVENTING ELECTROCUTION
  • 2.4.10 VISIBILITY
  • 2.4.11 WORKING ON ICY OR SNOW-COVERED SURFACES
  • 2.4.12 PREVENTING DAMAGE CAUSED BY THE WORK EQUIPMENT
  • 2.4.13 WORKING ON LOOSE GROUND
  • 2.4.14 PARKING THE MACHINE
• 2.5 TRANSPORTING THE MACHINE ON OTHER VEHICLES
  • 2.5.1 LOADING AND UNLOADING THE MACHINE
  • 2.5.2 TRANSPORT
• 2.6 BATTERY
  • 2.6.1 PREVENTING RISKS THAT MAY BE DUE TO THE BATTERY
  • 2.6.2 STARTING WITH BOOSTER CABLES
• 2.7 PRECAUTIONS FOR EMERGENCY RECOVERY
• 2.8 LIFTING OBJECTS WITH LIFTING DEVICE (OPTIONAL EQUIPMENT)
  • 2.8.1 SAFETY RULES FOR LIFTING OBJECTS
• 2.9 PRECAUTIONS TO BE TAKEN DURING MAINTENANCE
  • 2.9.1 WARNING PLATES
  • 2.9.2 TOOLS
  • 2.9.3 PERSONNEL
  • 2.9.4 EQUIPMENT
  • 2.9.5 WORKING UNDER THE MACHINE
  • 2.9.6 STABILITY
  • 2.9.7 REPAIR WELDS
  • 2.9.8 KEEPING THE MACHINE CLEAN
  • 2.9.9 USE OF THE ENGINE DURING MAINTENANCE
  • 2.9.10 PERIODICAL CHANGE OF THE SAFETY RELATED PARTS
  • 2.9.11 STOP THE ENGINE BEFORE CARRYING OUT ANY MAINTENANCE OPERATION OR INSPECTION
  • 2.9.12 BATTERY MAIN SWITCH PRECAUTIONS
  • 2.9.13 RULES TO BE FOLLOWED DURING FUEL OR OIL TOPPING UP
  • 2.9.14 CHECKING THE COOLANT LEVEL IN THE RADIATOR
  • 2.9.15 USING LAMPS
  • 2.9.16 PRECAUTIONS TO BE TAKEN WHEN HANDLING THE BATTERY AND THE ALTERNATOR
  • 2.9.17 PRECAUTIONS CONCERNING THE STARTER
  • 2.9.18 HANDLING HIGH-PRESSURE PIPES
  • 2.9.19 PRECAUTIONS TO BE TAKEN WHEN WORKING ON HIGH- PRESSURE SYSTEMS
  • 2.9.20 PRECAUTIONS FOR MAINTENANCE WORK INVOLVING HIGH TEMPERATURES AND PRESSURES
  • 2.9.21 HYDRAULIC ACCUMULATOR
  • 2.9.22 COOLING FAN AND FAN BELT
  • 2.9.23 CHEMICAL HAZARD
  • 2.9.24 WASTE MATERIALS
  • 2.9.25 SERVICING THE AIR CONDITIONER
  • 2.9.26 PRECAUTIONS CONCERNING TECHNOPOLYMERS AND ELASTOMERS
  • 2.9.27 PRECAUTIONS TO BE TAKEN WHEN INFLATING THE TYRES
  • 2.9.28 PRECAUTIONS FOR THE INSTALLATION OF THE EXHAUST SYSTEM TAILPIPE
  • 2.9.29 PRECAUTIONS TO BE TAKEN WHEN USING SYNTHETIC BIODEGRADABLE OIL TYPE «HEES»
  • 2.9.30 FINAL DISPOSAL OF THE MACHINE
• 3.1 SAFETY LOCKS
  • 3.1.1 FRONT LOADER LOCKS
  • 3.1.2 BACKHOE LOCKS
• 3.2 GENERAL VIEWS
  • 3.2.1 FRONT GENERAL VIEW
  • 3.2.2 BACKHOE GENERAL VIEW
  • 3.2.3 CAB INSIDE GENERAL VIEW
    • 3.2.3.1 CAB INSIDE GENERAL VIEW (mechanical backhoe controls)
    • 3.2.3.2 CAB INSIDE GENERAL VIEW (backhoe servo controls)
• 3.3 INSTRUMENTS AND CONTROLS
  • 3.3.1 FRONT INSTRUMENTS
  • 3.3.2 SIDE INSTRUMENTS
  • 3.3.3 PUSH BUTTONS ON THE FRONT LOADER CONTROL LEVER
  • 3.3.4 PUSH BUTTON ON THE GEARSHIFT LEVER
  • 3.3.5 CAB SWITCHES AND ELECTRIC ACCESSORIES
  • 3.3.6 MACHINE CONTROLS
    • 3.3.6.1 MACHINE CONTROLS (version with mechanically-controlled backhoe)
    • 3.3.6.2 MACHINE CONTROLS (version with servo-assisted backhoe)
    • 3.3.6.3 ADJUSTING THE CONTROLS
• 3.4 FUSES AND RELAYS
  • 3.4.1 CENTRAL UNIT FUSES – RELAYS AND ENGINE LINE
    • 3.4.1.1 FUSES
    • 3.4.1.2 RELAYS
  • 3.4.2 VENTILATION, HEATING AND AIR CONDITIONING FUSES AND RELAYS
    • 3.4.2.1 FUSES
    • 3.4.2.2 RELAYS
• 3.5 GUARDS, CAB AND DRIVER’S SEAT
  • 3.5.1 ENGINE HOOD
  • 3.5.2 CAB
  • 3.5.3 VENTILATION AND HEATING
  • 3.5.4 AIR CONDITIONER (if installed)
  • 3.5.5 SEAT
    • 3.5.5.1 SEAT (Standard mod. CAB SEATING)
  • 3.5.6 SEAT (OPTIONAL)
    • 3.5.6.1 PNEUMATIC SUSPENSION SEAT (optional mod. CAB SEATING)
    • 3.5.6.2 SEAT (Standard mod. SEARS SEATING)
    • 3.5.6.3 PNEUMATIC SUSPENSION SEAT (optional mod. SEARS SEATING)
  • 3.5.7 SAFETY BELT
    • 3.5.7.1 STANDARD SAFETY BELTS
    • 3.5.7.2 SAFETY BELTS WITH WINDER
  • 3.5.8 FIRE EXTINGUISHER
  • 3.5.9 FIRST AID KIT
  • 3.5.10 TECHNICAL DOCUMENTATION
  • 3.5.11 STORAGE COMPARTMENT
  • 3.5.12 REFUELLING PUMP (If installed)
• 3.6 USE OF THE MACHINE
  • 3.6.1 CHECKS TO BE CARRIED OUT BEFORE STARTING THE ENGINE
    • 3.6.1.1 VISUAL CHECKS
    • 3.6.1.2 OPERATIONAL CHECKS
  • 3.6.2 STARTING THE ENGINE
    • 3.6.2.1 STARTING WITH WARM ENGINE OR IN TEMPERATE CLIMATES
    • 3.6.2.2 STARTING WITH COLD ENGINE OR IN COLD CLIMATES
  • 3.6.3 WARMING THE ENGINE
  • 3.6.4 HEATING THE HYDRAULIC OIL
  • 3.6.5 HOW TO MOVE THE MACHINE
    • 3.6.5.1 ENGAGING THE FOUR-WHEEL DRIVE
    • 3.6.5.2 WORKING ON SLOPES
    • 3.6.5.3 MAXIMUM IMMERSION DEPTH
• 3.7 PARKING THE MACHINE
  • 3.7.1 PARKING ON LEVEL GROUND
  • 3.7.2 PARKING ON SLOPES
• 3.8 STOPPING THE ENGINE
• 3.9 TRANSPORTATION
  • 3.9.1 PRECAUTIONS FOR TRANSPORTING MACHINE
  • 3.9.2 SELECT TRANSPORTATION METHOD
  • 3.9.3 PRECAUTIONS FOR LOADING AND UNLOADING WITH TRAILER
  • 3.9.4 PROCEDURES FOR LOADING AND SECURING MACHINE ON THE TRAILER
    • 3.9.4.1 LOADING MACHINE ON THE TRAILER
    • 3.9.4.2 SECURING THE MACHINE
  • 3.9.5 LIFTING THE MACHINE
• 3.10 PRECAUTIONS TO BE TAKEN IN THE COLD SEASON
  • 3.10.1 FUEL AND LUBRICANTS
  • 3.10.2 COOLANT
  • 3.10.3 BATTERY
  • 3.10.4 OTHER PRECAUTIONS
  • 3.10.5 PRECAUTIONS TO BE TAKEN AT THE END OF WORK
• 3.11 PRECAUTIONS TO BE TAKEN AT THE END OF THE WINTER
• 3.12 USING THE MACHINE AS A LOADER
  • 3.12.1 BUCKET POSITION INDICATOR
  • 3.12.2 ORGANIZING THE WORK AREA
    • 3.12.2.1 LOADING HEAPED AND LEVEL MATERIAL
    • 3.12.2.2 LOADING OPERATIONS ON SLOPES
  • 3.12.3 CHANGING THE STANDARD FRONT BUCKET
• 3.13 USING THE MACHINE AS AN EXCAVATOR
  • 3.13.1 POSITIONING THE BUCKET ACCORDING TO THE WORK THAT MUST BE CARRIED OUT
  • 3.13.2 POSITIONING THE MACHINE FOR DIGGING OPERATIONS
  • 3.13.3 SLIDING THE BACKHOE UNIT SIDEWARDS
  • 3.13.4 DIGGING METHOD
  • 3.13.5 LIFTING LOADS WITH EQUIPMENT
    • 3.13.5.1 LIFTING CAPACITIES
    • 3.13.5.2 LIFTING CAPACITIES
    • 3.13.5.3 CHANGING THE BACKHOE BUCKET
• 3.14 LONG PERIODS OF INACTIVITY
  • 3.14.1 PREPARING THE MACHINE FOR A LONG PERIOD OF INACTIVITY
  • 3.14.2 PREPARING THE ENGINE FOR A LONG PERIOD OF INACTIVITY
  • 3.14.3 MAINTENANCE DURING A PERIOD OF INACTIVITY
  • 3.14.4 RESTARTING THE ENGINE
  • 3.14.5 AFTER THE PERIOD OF INACTIVITY
  • 3.14.6 AMBIENT TEMPERATURE RANGE FOR OPERATION AND LONG TERM STORAGE
• 3.15 TROUBLESHOOTING
  • 3.15.1 HOW TO REMOVE THE MACHINE
  • 3.15.2 AFTER THE FUEL HAS RUN OUT
  • 3.15.3 IF THE BATTERY IS DOWN
    • 3.15.3.1 STARTING WITH BOOSTER CABLES
  • 3.15.4 OTHER TROUBLES
    • 3.15.4.1 ELECTRICAL CIRCUIT
    • 3.15.4.2 HYDRAULIC SYSTEM
    • 3.15.4.3 BRAKING SYSTEM
    • 3.15.4.4 CONVERTER
    • 3.15.4.5 ENGINE
• 4.1 GUIDE TO MAINTENANCE
• 4.2 MAINTENANCE NOTES
  • 4.2.1 NOTES REGARDING THE ENGINE
    • 4.2.1.1 ENGINE OIL
    • 4.2.1.2 COOLANT
    • 4.2.1.3 FUEL
  • 4.2.2 NOTES REGARDING THE HYDRAULIC SYSTEM
  • 4.2.3 NOTES REGARDING THE ELECTRIC SYSTEM
  • 4.2.4 NOTES REGARDING LUBRICATION
  • 4.2.5 PARTS SUBJECT TO WEAR THAT PERIODICALLY NEED CHANGING
• 4.3 FUEL AND LUBRICANTS
  • 4.3.1 HOMOLOGATED SYNTHETIC BIODEGRADABLE LUBRICANTS “HEES”
• 4.4 DRIVING TORQUES
  • 4.4.1 STANDARD DRIVING TORQUES FOR SCREWS AND NUTS
  • 4.4.2 SPECIFIC DRIVING TORQUES FOR SCREWS AND NUTS
  • 4.4.3 STANDARD DRIVING TORQUES FOR HOSES WITH ORFS
• 4.5 LUBRICATION
  • 4.5.1 LUBRICATION DIAGRAM
  • 4.5.2 LUBRICATION DIAGRAM (4in1 bucket and pallet forks)
  • 4.5.3 LUBRICATION DIAGRAM (front bucket quick couplings)
  • 4.5.4 LUBRICATION DIAGRAM (offset device)
  • 4.5.5 LUBRICATION CHART (For hydraulically-controlled sliding plate)
  • 4.5.6 LUBRICATION DIAGRAM (for telescopic boom)
• 4.6 PERIODICAL CHANGE OF THE SAFETY RELATED COMPONENTS
  • 4.6.1 SAFETY RELATED PARTS
    • 4.6.1.1 FUEL SYSTEM
    • 4.6.1.2 DELIVERY HYDRAULIC SYSTEM
    • 4.6.1.3 FRONT LOADER HYDRAULIC SYSTEM
    • 4.6.1.4 BACKHOE HYDRALIC SYSTEM
    • 4.6.1.5 OPERATOR’S SAFETY
• 4.7 MAINTENANCE PLAN
• 4.8 MAINTENANCE PROCEDURES
  • 4.8.1 WHEN REQUIRED
    • 4.8.1.a CHECKING, CLEANING OR CHANGING THE ENGINE AIR FILTERS
    • 4.8.1.b CHECKING AND CLEANING THE CAB AIR FILTER
    • 4.8.1.c CHECKING AND CLEANING THE AIR RECIRCULATION FILTER (only for machines with air conditioner)
    • 4.8.1.d CHECKING THE DETERGENT LEVEL IN THE WINDSHIELD WASHER RESERVOIR AND TOPPING UP
    • 4.8.1.e CHECKING THE WINDSHIELD WIPER BLADES
    • 4.8.1.f LUBRICATING THE CAB DOOR HINGES
    • 4.8.1.g FUSES AND RELAYS – CHECK AND CHANGE
    • 4.8.1.h BLEEDING THE BRAKING CIRCUIT
    • 4.8.1.i CHECKING AND ADJUSTING THE WHEEL TOE-IN
    • 4.8.1.j CHECKING THE BRAKING EFFICIENCY
    • 4.8.1.k CHECKING AND ADJUSTING THE PARKING BRAKE
    • 4.8.1.l CHECKING AND ADJUSTING THE BRAKE PEDAL STROKE
    • 4.8.1.m ADJUSTING THE AUTOMATIC RETURN- TO-DIG DEVICE OF THE FRONT BUCKET (if installed)
    • 4.8.1.n CHECKING AND ADJUSTING THE STABILIZER SLACK
    • 4.8.1.o 1st STAGE DECANTER DRAINAGE
    • 4.8.1.p TYRE ROTATION
  • 4.8.2 MAINTENANCE INTERVALS IN CASE OF USE OF THE HYDRAULIC BREAKER
    • 4.8.2.a CHANGING THE HYDRAULIC OIL FILTER
    • 4.8.2.b CHANGING THE HYDRAULIC OIL
  • 4.8.3 CHECKS TO BE CARRIED OUT BEFORE STARTING THE ENGINE
    • 4.8.3.a VARIOUS CHECKS
    • 4.8.3.b CHECKING THE COOLANT LEVEL
    • 4.8.3.c CHECKING THE FUEL LEVEL
    • 4.8.3.d CHECKING THE ENGINE OIL LEVEL
  • 4.8.4 MAINTENANCE EVERY 10 HOURS OF OPERATION
    • 4.8.4.a LUBRICATING THE JOINTS
  • 4.8.5 MAINTENANCE AFTER THE FIRST 50 HOURS OF OPERATION (Only for machines in which synthetic biodegradable oil type HEES is used)
  • 4.8.6 MAINTENANCE EVERY 50 HOURS OF OPERATION
    • 4.8.6.a CHECKING THE HYDRAULIC OIL LEVEL
    • 4.8.6.b CHECKING THE FLUID LEVEL IN THE RADIATOR
    • 4.8.6.c CHECKING THE BRAKING SYSTEM OIL LEVEL
    • 4.8.6.d LUBRICATING THE PROPELLER SHAFTS
    • 4.8.6.e LUBRICATING THE FRONT AXLE JOINTS AND CENTRAL COUPLING AND THE REAR AXLE JOINTS
    • 4.8.6.f CHECKING THE TYRE PRESSURE
    • 4.8.6.g 2nd STAGE DECANTER DRAINAGE
  • 4.8.7 MAINTENANCE AFTER THE FIRST 250 HOURS OF OPERATION
  • 4.8.8 MAINTENANCE EVERY 250 HOURS OF OPERATION
    • 4.8.8.a CHECKING THE ALTERNATOR-FAN BELT
    • 4.8.8.b CHECKING AND ADJUSTING THE A/C COMPRESSOR BELT TENSION (only for machines with air conditioner)
    • 4.8.8.c CHECKING THE BATTERY ELECTROLYTE LEVELAND TOPPING UP
    • 4.8.8.d CHECKING THE FRONT AXLE OIL LEVELS
    • 4.8.8.e CHECKING THE REAR AXLE OIL LEVEL
    • 4.8.8.f CHECKING THE HYDRAULIC TRANSMISSION OIL LEVEL
    • 4.8.8.g CHECKING THE WHEEL NUT DRIVING TORQUE
  • 4.8.9 MAINTENANCE AFTER THE FIRST 500 HOURS OF OPERATION (Only for machines in which synthetic biodegradable oil type HEES is used)
  • 4.8.10 MAINTENANCE EVERY 500 HOURS OF OPERATION
    • 4.8.10.a CHANGING THE ENGINE OIL
    • 4.8.10.b CHANGING THE ENGINE OIL FILTER
    • 4.8.10.c CHANGING THE HYDRAULIC SYSTEM OIL FILTER
    • 4.8.10.d CHANGING THE FUEL FILTERS
    • 4.8.10.e DRAINING THE FUEL TANK
    • 4.8.10.f DRAINING THE HYDRAULIC OIL TANK (only for machines in which synthetic biodegradable oil type HEES is used )
    • 4.8.10.g CLEANING THE OUTSIDE OF THE RADIATOR
    • 4.8.10.h CLEANING THE OUTSIDE OF THE A/C CONDENSER (only for machines with air conditioner)
  • 4.8.11 MAINTENANCE EVERY 1000 HOURS OF OPERATION
    • 4.8.11.a CHANGING THE FRONT AXLE OIL
    • 4.8.11.b CHANGING THE REAR AXLE OIL
    • 4.8.11.c CHANGING THE HYDRAULIC TRANSMISSION OIL
    • 4.8.11.d CHANGING THE HYDRAULIC TRANSMISSION OIL FILTER
  • 4.8.12 MAINTENANCE EVERY 2000 HOURS OF OPERATION
    • 4.8.12.a CHANGING THE HYDRAULIC OIL AND CLEANING THE INTAKE FILTER
    • 4.8.12.b CLEANING OF THE COOLING SYSTEM AND CHANGING THE COOLANT
    • 4.8.12.c CHANGING THE BRAKING SYSTEM OIL
    • 4.8.12.d CHECKING THE ALTERNATOR AND THE STARTER
    • 4.8.12.e CHANGING THE ALTERNATOR BELT
    • 4.8.12.f CHECKING THE A/C COOLING GAS QUANTITY (only for machines with air conditioner)
  • 4.8.13 MAINTENANCE EVERY 3000 HOURS OF OPERATION
    • 4.8.13.a CHECKING THE ENGINE RETAINING SCREWS AND DAMPING ELEMENTS
    • 4.8.13.b CHECKING AND ADJUSTING THE ENGINE VALVE CLEARANCE AND THE INJECTION TIMING ADVANCE
  • 4.8.14 MAINTENANCE EVERY 4000 HOURS OF OPERATION
    • 4.8.14.a CHANGING THE A/C DEWATERING FILTER (Only for machines with air conditioner)
    • 4.8.14.b CHECKING THE OPERATING CONDITIONS OF THE A/C COMPRESSOR (Only for machines with air conditioner)
    • 4.8.14.c CHANGING THE ENGINE THERMOSTATIC VALVE
• 4.9 END OF SERVICE LIFE
• 5.1 TECHNICAL DATA
  • 5.1.1 STANDARD OVERALL DIMENSIONS
    • 5.1.1.1 OVERALL DIMENSIONS WITH STANDARD ARM
    • 5.1.1.2 OVERALL DIMENSIONS WITH TELESCOPIC ARM
  • 5.1.2 TECHNICAL CHARACTERISTICS
  • 5.1.3 WORKING RANGES
    • 5.1.3.1 WORKING RANGE LOADER AND BACKHOE
  • 5.1.4 LIFTING CAPACITIES
    • 5.1.4.1 LIFTING CAPACITIES (STANDARD BOOM)
    • 5.1.4.2 LIFTING CAPACITIES (BOOM WITH OFFSET DEVICE)
• 6.1 AUTHORIZED OPTIONAL EQUIPMENT
  • 6.1.1 PRECAUTIONS REGARDING SAFETY
  • 6.1.2 PRECAUTIONS REGARDING THE INSTALLATION OF EQUIPMENT
• 6.2 SPECIFICATIONS
  • 6.2.1 ARM-PIN INFORMATION
• 6.3 ATTACHMENT GUIDE
  • 6.3.1 COMBINATIONS OF WORK EQUIPMENT
  • 6.3.2 ATTACHMENT CONFIGURATION
• 6.4 FRONT EQUIPMENT QUICK COUPLING DEVICES
  • 6.4.1 MANUAL QUICK COUPLING
  • 6.4.2 HYDRAULIC QUICK COUPLING FOR STANDARD BUCKET
    • 6.4.2.1 COUPLING
    • 6.4.2.2 RELEASE
  • 6.4.3 HYDRAULIC QUICK COUPLING FOR 4in1 BUCKET AND OPTIONAL EQUIPMENT
• 6.5 PALLET FORKS
  • 6.5.1 LIFTING CAPACITIES (PALLET FORKS)
  • 6.5.2 DESCRIPTION
  • 6.5.3 USING THE FORKS
  • 6.5.4 MAINTENANCE
• 6.6 4in1 BUCKET
  • 6.6.1 DESCRIPTION AND CONTROLS
  • 6.6.2 SAFETY DEVICES
  • 6.6.3 INSTALLING THE 4in1 BUCKET
  • 6.6.4 USING THE 4in1 BUCKET
  • 6.6.5 MAINTENANCE
• 6.7 FORKS FOR PALLET ON BUCKET 4 IN 1
  • 6.7.1 DESCRIPTION
  • 6.7.2 LIFTING CAPACITY (FORKS FOR ON BUCKET 4 IN 1)
  • 6.7.3 USING THE FORKS
    • 6.7.3.1 PREPARING THE PALLET FORKS FOR USE
    • 6.7.3.2 OVERTURNING THE FORKS
  • 6.7.4 REMOVING THE FORKS
  • 6.7.5 INSTALLING THE FORKS
  • 6.7.6 MAINTENANCE
  • 6.7.7 INSTALLING THE 4in1 BUCKET
• 6.8 BACKHOE TELESCOPIC ARM
  • 6.8.1 DESCRIPTION AND CONTROL
    • 6.8.1.1 CONTROL (version with mechanically- controlled backhoe)
    • 6.8.1.2 CONTROL (version with servo-assisted backhoe)
  • 6.8.2 SAFETY DEVICES
  • 6.8.3 USING THE TELESCOPIC ARM
  • 6.8.4 MAINTENANCE
    • 6.8.4.1 ADJUSTING THE GUIDE SLACK
• 6.9 CONFIGURATION FOR THE INSTALLATION OF THE HYDRAULIC BREAKER
  • 6.9.1 DESCRIPTION AND CONTROL
    • 6.9.1.1 CONTROL (version with mechanically- controlled backhoe)
    • 6.9.1.2 CONTROL (version with servo-assisted backhoe)
  • 6.9.2 USE OF THE HYDRAULIC BREAKER AND RULES TO BE OBSERVED
    • 6.9.2.1 HYDRAULIC BREAKER
  • 6.9.3 INSTALLING AND REMOVING THE HYDRAULIC BREAKER
    • 6.9.3.1 INSTALLING THE BREAKER
    • 6.9.3.2 REMOVING THE HAMMER
  • 6.9.4 USING THE HAMMER
  • 6.9.5 MAINTENANCE
• 6.10 APPLICATION OF THE OFFSET DEVICE
  • 6.10.1 DESCRIPTION AND CONTROL
    • 6.10.1.1 CONTROL (version with mechanically- controlled backhoe)
    • 6.10.1.2 CONTROL (version with servo-assisted backhoe)
  • 6.10.2 MAINTENANCE
• 6.11 CONFIGURATION FOR THE USE OF OPTIONAL EQUIPMENT WITH UNIDIRECTIONAL OIL FLOW
  • 6.11.1 DESCRIPTION AND CONTROL
    • 6.11.1.1 CONTROL (version with mechanically- controlled backhoe)
    • 6.11.1.2 CONTROL (version with servo-assisted backhoe)
  • 6.11.2 INSTALLING AND CONNECTING THE EQUIPMENT
  • 6.11.3 MAINTENANCE
• 6.12 CONFIGURATION FOR THE USE OF THE CLAMSHELL BUCKET
  • 6.12.1 DESCRIPTION AND CONTROL
    • 6.12.1.1 CONTROL (version with mechanically-controlled backhoe)
    • 6.12.1.2 CONTROL (version with servo-assisted backhoe)
  • 6.12.2 INSTALLING THE CLAMSHELL BUCKET
  • 6.12.3 USING THE CLAMSHELL BUCKET
  • 6.12.4 MAINTENANCE
• 6.13 TELESCOPIC BOOM WITH PRE-INSTALLATION FOR HYDRAULIC BREAKER AND OPTIONAL TOOLS
• 6.14 CONFIGURATION FOR THE USE OF THE HAND HYDRAULIC HAMMER
  • 6.14.1 DESCRIPTION AND CONTROL
  • 6.14.2 INSTALLING AND REMOVING THE HAND HAMMER
    • 6.14.2.1 CONNECTING THE HAND HAMMER
    • 6.14.2.2 REMOVING THE CONNECTIONS
  • 6.14.3 USING THE HAMMER
  • 6.14.4 MAINTENANCE
• 6.15 LOAD STABILIZER SYSTEM (LSS) (Optional)
  • 6.15.1 LOAD STABILIZER SYSTEM (LSS) ACCUMULATOR
• 6.16 REAR EQUIPMENT MECHANICAL QUICK COUPLING DEVICE
  • 6.16.1 EQUIPMENT COUPLING AND RELEASE PROCEDURE
    • 6.16.1.1 COUPLING PROCEDURE
    • 6.16.1.2 RELEASE PROCEDURE
  • 6.16.2 MAINTENANCE
  • 6.16.3 MAINTENANCE PLAN
    • 6.16.3.1 DAILY
    • 6.16.3.2 WEEKLY (AT LEAST ONCE PER WEEK)
    • 6.16.3.3 TROUBLESHOOTING
• 6.17 HYDRAULICALLY-CONTROLLED SLIDING PLATE FOR BACKHOE