$ 0
0
$ 0
0

Mustang 4000V Skid Steer Loader Operator Manual

Format: PDF (Printable Document)

File Language: English

File Size: 17.89 MB (Speed Download Link)

Brand: Mustang

Model: 4000V

Machine Type: Skid Steer Loader

Publication No.: 50950005 (Rev. C)

Edition Date: July 2014

Type of Document: Operator Manual (operation, controls, safety and routine maintenance)

Searchable: Yes, text is searchable and copyable

Delivery: Instant download after payment

Categories: ,

$ 40

Share:

Mustang 4000V Skid Steer Loader Operator Manual

Before anyone drives off, the Mandatory Safety Shutdown Procedure is the section I point them to in the Mustang 4000V Skid Steer Loader Operator Manual. It sits in the Safety chapter, next to Safety Reminders, Potential Hazards and the decal pages, and it covers how to leave the machine properly.

This is publication number 50950005 (Rev. C), edition date July 2014, in English, written for the Mustang 4000V. It is the book to have when a customer takes the loader over, or when a used machine turns up without one. It goes from Loader Identification and the Control/Indicator Symbols through the controls, the Information Center Electronic Display, specifications and fault codes.

What this manual helps you do

  • Start with Loader Identification and the Product and Component Plate Locations, so you know where to find the plates on the machine.
  • Operate the controls using the chapters on Engine Speed Control, Two-Speed Drive (Travel Mode Only), the Hydraglide Ride Control System and Float Control.
  • Check the Operator Restraint Bar, Upper-Torso Restraint, Safety Interlock System, Parking Brake and Lift Arm Support Device against the Controls and Safety Equipment pages.
  • Look up the Service Interval and Maintenance Log, plus Engine Oil, Engine Oil Filter and Engine Oil Pressure, when a service is due.
  • Follow the DTC Screen and DTC Detailed Information pages, and the Engine Diagnostic Chart, when a warning appears on the display.

Who this is for

A rental fleet or dealer handing a 4000V to a new operator will use the safety and controls chapters for the walk-around. An owner-operator or a buyer of a used machine can use it for service intervals, the Torque Specifications, and fault code lookup.

Print the shutdown procedure page and keep it with the machine for every new customer.

Preview of the Mustang 4000V Skid Steer Loader Operator Manual (PDF, sample pages)

Does this manual fit your machine?

Mustang model 4000V
Machine type Skid Steer Loader
Publication No. 50950005 (Rev. C)
Edition date July 2014

Check the model and serial number on your machine’s serial plate before ordering.

What’s inside

  • Fault / error codes: DTC Screen; DTC Detailed Information
  • Troubleshooting: Engine Diagnostic Chart; Engine Diagnostic Chart (cont.); Troubleshooting
  • Torque values: Torque Specifications
  • Maintenance intervals / schedule: Service Interval; Maintenance Log
  • Lubrication, oils, fluids and capacities: Engine Oil; Engine Oil Filter; Engine Oil Pressure
  • Technical specifications: Specifications; Loader Specifications; Dimensional Specifications
  • Removal, installation and overhaul procedures: Installation; Removal; Sliding Side Window Removal Procedure
  • Adjustments and calibration: Bar Graph Limits Adjust; Fuel Tank Calibration; Adjustments

FAQ

Where do I find what the warning lamps and display mean?
Open Indicator and Warning Lamp Display and Information Center Electronic Display, which also has Display Modes and a Settings Menu. The Control/Indicator Symbols pages explain the symbols.

Does it cover fault codes?
Yes, there are DTC Screen and DTC Detailed Information sections. The Troubleshooting section adds an Engine Diagnostic Chart that continues over two pages.

Which safety decals are shown?
Both ANSI-Style and ISO-Style (used Internationally) decals are shown, inside the ROPS/FOPS and in the Engine Compartment. That helps you check that every decal on a machine is in place.

Are any adjustments or procedures in the book?
Yes, it has Bar Graph Limits Adjust and Fuel Tank Calibration under Adjustments. There is also a Sliding Side Window Removal Procedure.

More books for this machine

📘 Show Index

Table of Contents:

  • Introduction
    • Loader Identification
    • Control/Indicator Symbols
      • Power Off
      • Power On
      • Engine Start
      • Battery Charge
      • Electrical Power
      • Worklight w/Tail Lights
      • Worklight
      • Safety Alert
      • Hazard Flasher
      • Fasten Seatbelt
      • Horn
      • Volume – Full
      • Volume – Half Full
      • Volume – Empty
      • H-L
      • High – Low
      • Neutral
      • Forward
      • Reverse
      • Parking Brake
      • Engine Air Filter
      • Engine Oil
      • Engine Oil Filter
      • Engine Oil Pressure
      • Fuel Filter
      • Engine Temperature
      • Hydraulic System
      • Hydraulic Oil Temperature
      • Hydraulic Oil Filter
      • Grease Lubrication Point
      • Glow Indicator Lamp
      • Diesel Fuel
      • Chaincase Oil
      • Clockwise Rotation
      • Counterclockwise Rotation
      • Fast
      • Slow
      • Ride Control
      • Engine Malfunction Shutdown
      • Bucket – Float
      • Bucket – Rollback
      • Bucket – Dump
      • Lift Arm – Lower
      • Lift Arm – Raise
      • Service Hours
      • Lift Point
      • Tie-Down
      • Diesel Water Separator
      • Power-A-Tach®
      • Service Interval
    • Control/Indicator Symbols, cont
      • Low Fuel Alarm
      • Master Light Switch
      • Position Lights
      • Engine Speed Control
  • Safety
    • Mandatory Safety Shutdown Procedure
    • Safety Reminders
    • Potential Hazards
    • Safety Decals
      • New Decal Application
    • ANSI-Style Safety Decals inside the ROPS/FOPS
    • ANSI-Style Safety Decals in the Engine Compartment
    • ISO-Style (used Internationally) Safety Decals inside the ROPS/FOPS
    • ISO-Style (used Internationally) Safety Decals in the Engine Compartment
    • Product and Component Plate Locations
  • Controls and Safety Equipment
    • Guards and Shields
    • Operator Restraint Bar
    • Operator’s Seat
      • Figure 1 Operator’s Seat
    • Upper-Torso Restraint
    • Safety Interlock System
      • Hydraloc™
      • Testing the Safety Interlock System
    • ROPS/FOPS
    • Parking Brake
      • Figure 2 Parking Brake Switch
    • Horn
    • Rear Window Emergency Exit
    • Lift Arm Support Device
      • Installation
      • Removal
    • Accessory Plug
    • Dome Light
    • Work Lights
    • Heater (optional)
    • Heater and Air Conditioner (optional)
      • Figure 5 Heater/ Air Conditioner Controls
    • Engine Speed Control
      • Figure 6 Engine Speed Control
      • Figure 7 Foot Throttle (Joystick controls)
    • Two-Speed Drive (Travel Mode Only)
    • Hydraglide™ Ride Control System
    • Float Control
    • Attachment Mounting
      • All-Tach® Hitch
      • Power-A-Tach® System
    • Indicator and Warning Lamp Display
      • Figure 9 Indicator and Warning Lamp Display
      • Indicator and Warning Lamp Display
    • Information Center Electronic Display
      • Figure 10 Information Center Electronic Display
    • Display Modes – Information Center Electronic Display
      • Single Screen
      • Bar Graph Limits Adjust
      • Dual Screen
      • Multi-Screen
      • DTC Screen
      • DTC Detailed Information
    • Settings Menu – Information Center Electronic Display
      • Display Mode
      • Language
      • Fuel Level Source
      • Alarm Output
      • Demo Mode
      • Tier4 Popout Mode
      • Contrast /Backlight
      • Units
      • Fuel Tank Calibration
      • Factory settings
      • Supported Parameters
      • Information Center Electronic Display (cont.)
    • Instrument Panels
      • Figure 11 Left Panel
      • Left Panel
      • Right Panel
    • Joystick Controls
      • Figure 14 Dual Joystick Controls
      • Drive Controls
      • Lift/Tilt Control
    • Hand/Foot Controls
      • Figure 15 Hand/Foot Controls
      • Drive Controls
      • Lift/Tilt Controls
    • Auxiliary Hydraulic System
      • Standard-Flow Auxiliary Hydraulic Control
      • High-Flow Auxiliary Hydraulic Control (Optional)
    • Battery Disconnect Switch
      • Figure 18 Battery Disconnect Switch
  • Operation
    • Before Starting the Engine
    • Fuel
    • Starting the Engine
    • Cold-Starting
    • Cold-Starting Procedure
    • Stopping the Loader
    • Parking the Loader
    • Brake Release Operation (option)
    • Jump-starting
      • Figure 19 Positive (+) Remote Battery Terminal
    • Changing Attachments
      • Connecting Attachments
      • Connecting Auxiliary Hydraulic Couplings
      • Standard-Flow Auxiliary Hydraulics
      • Removing Attachments
    • Self-Leveling
    • Using a Bucket
      • Driving over Rough Terrain
      • Driving on an Incline
      • Digging with a Bucket
      • Loading a Bucket
      • Dumping the Load onto a Pile
      • Dumping the Load into a Truck (or Hopper)
      • Dumping the Load over an Embankment
      • Scraping with a Bucket
      • Leveling the Ground
    • Vibration Information
    • Vibration Measurement and Actions
      • Vibration Levels
    • Highway Travel
    • Storing the Loader
    • Removing Loader from Storage
    • Transporting the Loader
      • Figure 27 Left Front Tie-Down / Front Retrieval – Right Side Same
    • Lifting the Loader
  • Service
    • Dealer Services
    • Sliding Side Window Removal Procedure
      • Figure 29 Rail removed from window frame
    • Replacement Parts
    • Loader Raising Procedure
      • Figure 30 Loader Properly Blocked
    • Loader Lowering Procedure
    • Engine Compartment Access
      • Figure 31 Rear Door Latch Location
      • Figure 32 Engine Compartment Access Door and Cover
    • Tilting Back the ROPS/FOPS
      • Figure 33 ROPS/FOPS Lock Mechanism – Engaged
      • Figure 34 ROPS/FOPS Lock Mechanism – Disengaged
    • Adjustments
      • Control Handles
    • Removing Foreign Material
    • Lubrication
      • Figure 35 Service Locations
    • Chaincases
      • Checking and Adding Oil
      • Draining Oil
    • Drive Chains
      • Checking Chain Tension
      • Adjusting Chain Tension
    • Engine Air Cleaner
      • Figure 39 Dual-Element Air Cleaner
      • Access
      • Outer Element
      • Inner Element
      • Reinstallation
    • Engine Service
      • Figure 40 Engine Service Components
      • Checking Engine Mounting Hardware
      • Checking Engine Oil Level
      • Changing Engine Oil and Filter
      • Changing Fuel Filter
      • Checking the Water Separator
    • Engine Diagnostic Chart
      • Figure 44 Data Port for the Engine
      • Engine Diagnostic Chart (cont.)
    • Hydraulic System
      • Checking Hydraulic Oil Level
      • Changing Hydraulic Oil Filter
      • Changing Hydraulic Oil
    • Bucket Cutting Edge
    • Alternator
    • Wheel Nuts
    • Lift Arm Pivots
    • Cooling System
      • Checking Coolant Level
      • Cleaning the Cooling System
      • Draining/Flushing the Cooling System
    • Tires
      • Checking Tire Pressure
    • Heater/Air Conditioner Filters
    • Electrical System
      • Fuse Panel
      • Battery
  • Troubleshooting
  • Maintenance
    • Maintenance Log
  • Specifications
    • Loader Specifications
    • Standard Features
    • Optional Features
    • Dimensional Specifications
      • 27.0 ft3 (0.76 m3) Bucket w/14 x 17.5 Tires inches mm
    • Capacities and Ratings
      • 4000V
    • Common Materials and Densities
    • Bucket Selection
  • Torque Specifications
  • Warranty
    • MUSTANG WARRANTY SERVICE INCLUDES
    • MUSTANG WARRANTY DOES NOT INCLUDE
  • INDEX

Mustang PDF Manuals

Related Manuals

0
0
Your Cart
Your cart is emptyReturn to Shop