Takeuchi TB2150 Hydraulic Excavator Operators Manual (AN5E007)

Format: PDF (Printable Document)

File Language: English

File Pages: 389

File Size: 41.77 MB (Speed Download Link)

Brand: Takeuchi

Model: TB2150 Hydraulic Excavator

Book No: AN5E007

Serial No: 514600003-

Type of Document: Operators Manual

Categories: PDF, Takeuchi PDF

$ 40

Takeuchi TB2150 Hydraulic Excavator Operators Manual (AN5E007)

Takeuchi TB2150 Hydraulic Excavator Operators Manual (AN5E007) (SN 514600003-)

On a big machine like the Takeuchi TB2150, you’re usually working in tight, rough jobsites—deep trenching, lifting heavy pipe, loading trucks on uneven ground. This operators manual is what I’d keep handy to run the machine correctly and to understand how it should behave under load. If, for example, your boom starts dropping slowly when you hold it up with a load, this is the document I’d use to trace the function, check the right controls and modes, and decide whether it’s an operating issue or a hydraulic problem.

Applications & Use Cases

Set up daily checks so you’re inspecting pins, hoses, and fluid levels before you ever track onto the site.
Learn proper control use for smooth digging, swinging, and lifting on slopes without shocking the hydraulic system.
Verify correct operating modes for trenching, lifting, or hammer work to avoid overloading or overheating the system.
Improve visibility and load awareness, especially when working close to structures or traffic.

FAQ

Q: Is it worth printing parts of this manual?

A: Many techs print the schematic and key operating pages, laminate them, and keep them in the cab or service truck for quick reference.

Safety Note

Always release hydraulic pressure and secure all implements to the ground before inspecting, disconnecting, or routing any lines.

📘 Show Index

Takeuchi TB2150 Hydraulic Excavator Index:

Cover
Safety alert symbol
- Signal words
- Introduction
  - Foreword
  - Manual storage compartment
  - Serial numbers
- Machine description
  - Front, rear, left and right
  - Designated operations
  - Break-in period
- Notes on reading this manual
- Abbreviation used in this manual
Safety
- General precautions
- Precautions when preparing
- Precautions when starting
- Precautions when operating
- Precautions when stopping
- Precautions when transporting
- Precautions on maintenance
- Safety signs (decals)
Controls
- Names of components
- Covers
  - Starter key
  - Front covers (tool box)
  - Front cover (for maintenance)
  - Center cover
  - Fuel filler port
  - DEF/AdBlue® refill port
  - Right side cover
  - Left side cover
  - Engine hood
  - Maintenance cover
- Cab
  - Cab door
  - Front window
  - Lower front window
  - Side window
  - Emergency exit
- Seat and seat belt
  - Seat
  - Seat belt
  - Air Suspension Seat
- Multi-information display
  - Main Menu screen
  - Warning lamps
  - Indicators
  - Screen control key
  - Screen navigation
  - Switching images
- Switches
  - Starter switch
  - Engine shutdown switch
  - Throttle controller
  - Horn button
  - Deceleration button
  - Travel speed button
  - Auxiliary 1st switches
  - Auxiliary 2nd/4th switch
  - Third auxiliary hydraulic switch and button
  - Auxiliary 2/4 select button
  - Third auxiliary hard-lock switch (if equipped)
  - Wiper switch
  - Washer switch
  - Automatic deceleration switch
  - Power/Highland mode switch
  - Detent mode switch (Auxiliary 1st)
  - Light switch
  - Lift overload warning switch
  - Beacon lamp switch
  - Auxiliary 1st auto tank switch (option)
  - Standstill regeneration/Stop switch
- Levers and Pedals
  - Safety lock lever
  - Operating levers
  - Blade lever
  - Travel levers/pedals
  - Boom swing pedal
- Accessories
  - Air conditioner
  - Cup holder
  - Interior light
  - 12 V power socket
  - 24 V external power sockets
  - Radio
  - Radio (Bluetooth equipped)
  - Auxiliary hydraulic lines
  - Operating the machine with an accumulator
  - Load safety device
  - Fuel Supply Pump
  - USB port (If equipped)
  - Engine auto stop
  - Mirrors
  - Camera
Operation
- Before starting operation
  - Getting on or off the machine
  - Walk-around inspection
  - Daily inspection
- Starting and stopping the engine
  - Before starting the engine
  - Starting the Engine
  - Warming up the engine
  - Stopping the engine
- Operating the machine
  - Lever pattern (ISO pattern)
  - Lever pattern (G pattern) (If equipped)
  - Warming up the machine (hydraulic oil)
  - Inspection after warm-up
  - Operating the travel levers/pedals
  - Stopping travel
  - Operating the working equipment
- Operating procedures
  - Prohibited operations
  - Cautions on operating
  - Cautions on traveling on slopes
  - Getting out of mud
  - Operations possible with this machine
- Parking the machine
  - Parking
  - Inspection and checks after stopping the engine
- Handling in cold climates
  - Preparing for cold climates
  - Cautions after operations
  - After the cold climate
- Handling rubber crawlers
  - Prohibitions
  - Cautions
  - Preventing the rubber crawlers from coming off
- Standstill regeneration
Transport
- Loading and unloading
- Hoisting the machine
- Securing the machine
Maintenance
- General
  - Maintenance overview
  - Cautions on maintenance
- Service data
  - Fuel and lubricant table
  - Regularly replace the hydraulic oil
  - Handling of DEF/AdBlue®
  - List of consumables
  - List of tools (If equipped)
  - List of tightening torques
- Safety-critical parts
- Maintenance list
- Walk-around inspection
  - Inspecting by opening the engine hood and covers
  - Inspecting by walking around the machine
  - Inspecting while sitting in the operator’s seat
- Daily inspection (every 10 hours)
  - Inspecting and replenishing the coolant
  - Inspecting and replenishing the engine oil
  - Cleaning the dust screen
  - Inspecting the pre-fuel filter and draining
  - Inspecting the fuel level
  - Inspecting the hydraulic oil tank level and replenishing
  - Inspecting and cleaning the air cleaner
  - Lubricating the working equipment
  - Checking the DEF/AdBlue® level and refilling
- After the initial 50 hours (only for new machines)
  - Replacing the hydraulic oil return filter
  - Replacing the pilot line filter
  - Inspecting and adjusting the compressor belt (AC)
- Every 50 hours
  - Inspecting and adjusting the crawler tension
  - Draining the water from the fuel tank
  - Inspecting the battery fluid level and replenishing
- After the initial 250 hours (only for new machines)
  - Replacing the slew motor gear oil
  - Replacing the travel motor gear oil
- Every 250 hours
  - Inspecting the slew motor gear oil
  - Cleaning the cooler fins
  - Inspecting and adjusting the compressor belt (AC)
  - Cleaning the air filters (AC)
  - Cleaning the condenser (AC)
  - Inspecting the refrigerant (gas) level (AC)
- Every 500 hours
  - Lubricating the slew bearing
  - Replacing the engine oil and the oil filter
  - Inspecting the concentration of coolant additive
  - Inspecting the slew pinion gear
- Every 1000 hours
  - Replacing the hydraulic oil return filter
  - Replacing the pilot line filter
  - Replacing the slew motor gear oil
  - Replacing the travel motor gear oil
  - Replacing the engine cooling system
  - Replacing the air cleaner element
  - Replacing the air breather filter
  - Replacing the fuel filters
  - Replacing the DEF/AdBlue® supply module filter
  - Inspecting and adjusting the V-rib belt
  - Inspecting the engine installation condition
  - Inspecting the low-temperature starting device
- Every 3000 hours
  - Replacing the V-rib belt
- Every 4000 hours
  - Replacing the hydraulic oil and cleaning the suction strainer
- When required
  - Replacing the bucket teeth and the side cutters
  - Replacing the bucket
  - Adjusting the gap between the bucket and arm (If equipped)
  - Inspecting and replenishing the windshield washer fluid
  - Lubricating the levers and pedals
  - Inspecting the rubber crawlers
  - Replacing the rubber crawlers
  - Replacing the diesel particulate filter <Applicable machine models 514700002 or later>
- Every 2 year
  - Replacing the receiver dryer
- Maintenance during extended storage period
  - Storage procedures
Troubleshooting
- Symptoms that are not malfunctions
- If the engine overheats
- If the battery goes dead
- If a fuse blows
  - Inspecting and replacing the fuse
  - Inspecting the fusible link
- Restarting after adding fuel
  - Bleeding air from the fuel system
- Restarting when the DEF/AdBlue® level is low or the tank is empty
- If a warning lamp flashes
- Vehicle error code list
- Engine error code list
- Other symptoms
- Lowering the boom to the ground
- Towing
- If the cab is damaged
Specifications
- Basic Specifications
- Machine dimensions
- Operating ranges
- Lifting Capacities
Options
- General precautions
  - Safety precautions
  - Cautions when installing attachments
  - Cautions when operating attachments
- Attachment combination table
- Selecting a lever pattern
  - Switching the lever pattern
- Hydraulic breaker
  - Cautions on operating
  - Replacing the hydraulic oil regularly
- Travel alarm
- Optional equipment mass
- Biodegradable oil
  - Replacing the hydraulic oil with biodegradable oil
- Cab options
- Operating lever switch kit 1
  - Horn button
  - Deceleration button
  - Travel speed button
  - Auxiliary 1st switches
  - Auxiliary 2nd/4th switch
  - Auxiliary 2/4 select button
- Takeuchi Security System
  - Starter key
  - Starting the engine
  - Registering and deleting the starter key
  - If the master key is lost
  - Countries where the system can be used
- Takeuchi Fleet Management