Komatsu WA320-5 Operation and Maintenance Manual (VEAM240100)

📘 Show Index

Komatsu WA320-5 Index:

FOREWORD
- FOREWORD
- SAFETY INFORMATION
- INTRODUCTION
  - INTENDED USE
  - DIRECTIONS OF MACHINE
- NECESSARY INFORMATION
  - PIN/MACHINE SERIAL NO. PLATE AND POSITION
  - ENGINE SERIAL NO. PLATE AND POSITION
  - ROPS/FOPS-CAB SERIAL NO. PLATE
  - AXLE SERIAL NO. PLATE
  - TRANSMISSION SERIAL NO. PLATE
  - SEAT OPERATOR SERIAL NO. PLATE
  - POSITION OF SERVICE METER
  - TABLE TO ENTER SERIAL NO. AND DISTRIBUTOR
- CONTENTS
- DIMENSIONS, WEIGHTS AND OPERATING DATA
  - WA320-5H: DIMENSIONS, WEIGHTS AND OPERATING DATA
- CE-CONFORMING EQUIPMENT
  - CE-CONFORMING EQUIPMENT
  - MANUFACTURER-SUPPLIED CE-CONFORMING EQUIPMENT, ACCORDING TO DOCUMENT 421-93-H1900
SAFETY
- SAFETY LABELS
  - LOCATION OF SAFETY LABELS
  - PRESENTATION OF SAFETY LABELS
- GENERAL PRECAUTIONS
- PRECAUTIONS FOR OPERATION
  - STARTING ENGINE
  - OPERATION
  - TRANSPORTATION
  - BATTERY
  - TOWING
- PRECAUTIONS FOR MAINTENANCE
- PRECAUTIONS WITH TIRES
OPERATION
- GENERAL VIEW
  - GENERAL VIEW OF MACHINE
  - GENERAL VIEW OF CONTROLS AND GAUGES
- EXPLANATION OF COMPONENTS
  - MACHINE MONITOR
  - SWITCHES
  - CONTROL LEVERS, PEDALS
  - STEERING TILT LOCK LEVER
  - CAP AND COVER WITH LOCK
  - SAFETY BAR
  - TOWING PIN
  - GREASE PUMP
  - CAB DOOR INNER LOCK
  - CAB DOOR OPEN LOCK
  - CAB WINDOW OPEN LOCK CANCEL KNOB
  - FUSE
  - SLOW BLOW FUSE
  - POWER OUTLET
  - STORAGE BOX
  - AIR CONDITIONER
  - HANDLING CAB WIPER
- OPERATION
  - CHECK BEFORE STARTING ENGINE, ADJUST
  - STARTING ENGINE
  - OPERATIONS AND CHECKS AFTER STARTING ENGINE
  - STOPPING ENGINE
  - MOVING THE MACHINE (DIRECTIONAL, SPEED), STOPPING THE MACHINE
  - TURNING
  - OPERATION OF WORK EQUIPMENT
  - WORK POSSIBLE USING WHEEL LOADER
  - PRECAUTIONS FOR OPERATION
  - ADJUSTING WORK EQUIPMENT POSTURE
  - PARKING MACHINE
  - CHECK AFTER STOPPING ENGINE
  - CHECKS AFTER COMPLETION OF OPERATION
  - LOCKING
  - HANDLING THE TIRES
- TRANSPORTATION
  - TRANSPORTATION PROCEDURE
  - LOADING, UNLOADING WORK WITH TRAILERS
  - LIFTING MACHINE
- COLD WEATHER OPERATION
  - PRECAUTIONS FOR LOW TEMPERATURE
  - PRECAUTIONS AFTER COMPLETION OF WORK
  - AFTER COLD WEATHER
  - WARMING-UP OPERATION FOR STEERING HYDRAULIC CIRCUIT IN COLD WEATHER
- LONG-TERM STORAGE
  - BEFORE STORAGE
  - DURING STORAGE
  - AFTER STORAGE
- TROUBLESHOOTING
  - WHEN MACHINE RUNS OUT OF FUEL
  - TOWING THE MACHINE
  - IF BATTERY IS DISCHARGED
  - OTHER TROUBLE
MAINTENANCE
- GUIDES TO MAINTENANCE
- OUTLINES OF SERVICE
  - HANDLING OIL, FUEL, COOLANT, GREASE AND CARRYING OUT KOWA (Komatsu Oil Wear Analysis)
  - OUTLINE OF ELECTRIC SYSTEM
- WEAR PARTS
  - WEAR PARTS LIST
- FUEL, COOLANT AND LUBRICANTS
  - LUBRICATION CHART
  - PROPER SELECTION OF FUEL, COOLANT AND LUBRICANTS
- STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS
  - TORQUE LIST
- PERIODIC REPLACEMENT OF SAFETY CRITICAL PARTS
- MAINTENANCE SCHEDULE CHART
  - MAINTENANCE SCHEDULE CHART
- SERVICE PROCEDURE
  - INITIAL 50 HOURS SERVICE
  - INITIAL 250 HOURS SERVICE
  - WHEN REQUIRED
  - CHECK BEFORE STARTING
  - EVERY 50 HOURS SERVICE
  - EVERY 100 HOURS SERVICE
  - EVERY 250 HOURS SERVICE
  - EVERY 500 HOURS SERVICE
  - EVERY 1000 HOURS SERVICE
  - EVERY 2000 HOURS SERVICE
  - EVERY 4000 HOURS SERVICE
TECHNICAL DATA
- TECHNICAL DATA
- NOISE EMISSION LEVELS
- VIBRATION LEVELS
  - Operating condition:
  - Guide to Reduce Vibration Levels on Machine
ATTACHMENTS, OPTIONS
- SELECTING BUCKET AND TIRES
- MACHINE MONITOR WITH LOAD METER
  - EXPLANATION OF COMPONENTS
  - MACHINE MONITOR
- HANDLING MULTI-FUNCTION LEVER
  - EXPLANATION OF COMPONENTS
  - OPERATION
- CENTRAL LUBRICATION SYSTEM
  - OPERATING THE CENTRAL LUBRICATION SYSTEM
  - DISPLAY AND CONTROL UNIT
  - CHANGING THE LUBRICATION INTERVAL TIMES
INDEX
- INDEX
  - A
  - C
  - D
  - E
  - F
  - G
  - H
  - I
  - L
  - M
  - N
  - O
  - P
  - R
  - S
  - T
  - U
  - W
NOTES
- NOTES