Cat RT75 Rough Terrain Cranes Index:

• 49622 capitolo_00_EN_RT75_rev.03
• capitolo_01_EN_RT75_edizione 04-2012
• capitolo_02_EN_RT75_edizione 12-2011
• capitolo_03_EN_edizione 04-2012
  • III
  • Advice on safety when using mobile cranes.
    • INTRODUCTION
    • OPERATOR’S RESPONSIBILITIES
    • SIGNALLER’S RESPONSIBILITY
    • RESPONSIBILITIES OF ALL RELEVANT PERSONNEL
    • Management’s responsibilities
    • PLANNING THE WORKSITE
    • SAFETY CHECK BY OPERATOR
    • OPERATION PRECAUTIONS
  • General instructions
    • General
    • Access and cleaning
    • Machine operation
    • Maintenance
    • Electrical circuit
    • Hydraulic circuit
    • Tyres
    • Replacing the tyres
    • Instructions for reading the load table
      • Choosing the best configuration
      • Reduction of operating loads
      • Extension secured to brackets
      • Mounted extension
  • Special instructions for lifting on tyres
  • Special instructions for lifting on outriggers
  • Special instructions for lifting with mechanical element extended
  • Max. forces exerted on ground (daN)
  • Actions of the wind
  • Safety devices
    • Load and movement limiter
    • Limit stop device
      • In compliance with the safety regulations, the crane truck is equipped with:
      • 1. Lifting limit stop device that blocks the manoeuvre, preventing the block from getting too close to the boom head
      • 2. A “three dead turns” lowering limit stop device that prevents complete unwinding of the rope from the winch drum.
    • Deadman Safety Device
  • Machine operation
    • Engine starting
      • 1. Make sure the gearshift lever is in the neutral position “N”.
      • 2. Select the fast or slow gears according to needs (where applicable).
      • 3. Turn the ignition key.
      • 4. The battery level, braking system air circuit, engine oil pressure and coolant temperature warning lights on the instrument panel come on.
      • 5. Beep the horn.
      • 6. The parking brake must be applied.
      • 7. Turn the ignition switch to the second position to start the engine.
    • Switching off the engine
    • Securing the block (hook) to the truck crane
    • Driving on road
    • Driving on the worksite
    • Machine stabilization
    • Support surfaces
    • Extension of the boom
    • Lifting rope
    • Eccentric rigging (unbalanced)
    • Symmetrical rigging (balanced)
    • Changing the number of tackles
    • Blocks and hooks
    • Harnessing the load
  • Extensions assembly – disassembly
    • Work with main winch and auxiliary winch
    • Lifting with several mobile cranes
    • Towing
    • Transporting the crane on a self-propelled trailer
• capitolo_04_EN_RT75_edizione 12-2011a
• RCL RT75 EN ed. 12-2011a
  • 4.1 Layout of the RT75 system
  • 4.2 System Functions
  • 5.1 View Pages
    • 5.1.1 Operative Pages
    • 5.1.2 Configuration Pages
  • 6.1 INIT Page
  • 6.2 SETUP Page
    • 6.2.1 Work Settings: Machine Setup & Operating Mode
    • 6.2.2 Outriggers/Tyres
    • 6.2.3 Counterweight
    • 6.2.4 Block Assembly
    • 6.2.5 Main Boom/Jib
    • 6.2.6 Jib Storage
    • 6.2.7 Tackle
  • 6.3 LMI Page
  • 6.4 ENGINE Page
  • 6.5 ISAAC Pages
    • 6.5.1 ISAAC1 Page
    • 6.5.2 ISAAC 2 Page
  • 6.6 ISAAC Function
    • 6.6.1 Setting Boom Movement Limits (ISAAC1 Page)
    • 6.6.2 Setting Turret Slewing Limits (ISAAC2 Page)
    • 7.1.1 Display Page
    • 7.1.2 Date&Time Page
    • 7.1.3 Unit of Measurement Page
    • 7.1.4 Language Page
    • 7.1.5 Joystick Page
    • 7.1.6 Joystick Page
  • 8.1 Alarms
  • 8.2 List of Alarms
  • 9.1 Warning
  • 9.2 List of Warnings
• capitolo_05_EN_RT75_edizione 08-2012
• capitolo_06_EN_edizione 07-2012
  • VI
• capitolo_07_EN_edizione 04-2011