CNH FRONT BLADE WITH HALOGEN HEAD LAMPS KIT Installation Instructions (92711351)

Out where these machines work—snow, mud, gravel lots, farm yards—you’re hanging a front blade and lights on a tractor or loader that wasn’t born with them. This manual walks you through how to mount, route, and wire the CNH front blade and halogen lamps so they sit straight, clear the hood, and actually point where you’re driving. Say you’re adding a blade for winter work: you’ll trace the harness, bolt up the frame, align the lamps, then test everything before you push your first pile.

Applications & Use Cases

• Trace and route the wiring harness so it won’t chafe on the frame, steering, or blade linkages.
• Check bracket locations and verify hardware order so the blade sits square and the lamps don’t vibrate.
• Isolate electrical issues when the new lamps won’t fire by following the manual’s test steps and connector checks.
• Inspect clearances and cycle the blade through its travel to make sure hoses and wires don’t pinch or stretch.
• Bleed or recheck hydraulics after hookup, then align the blade and lamps and test under load.

FAQ

Q: Is this a PDF I can search on my laptop or phone?

A: It’s typically provided as a standard PDF, so you can search by keyword and zoom in on diagrams.

Q: Can I print just the wiring pages to take to the jobsite?

A: Yes, you can usually print selected pages, which is handy when you don’t want your whole manual covered in grease.

Safety Note

Always support the blade and lock out the machine before you route or inspect anything around the mounting frame.

CNH FRONT BLADE WITH HALOGEN HEAD LAMPS KIT Index:

1 SAFETY INFORMATION
Basic instructions – Important notice regarding equipment servicing. . . . . . . . . . . . . . . . . . . . . . . 1-1
Advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Safety rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
2 KIT CONTENT
Kit overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
3 GENERAL INFORMATION
Basic instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
4 PRE-ASSEMBLY
PREPARING FOR ASSEMBLY
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
5 ASSEMBLY
Install
Dozer blade – Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

CNH

92711312 – FRONT BLADE WITH HALOGEN HEAD LAMPS KIT
CASE CONSTRUCTION
856D Electro-Hydraulic Controls, Stage V –
ZF EC4 Transmission Control Unit
856D AWD Electro-Hydraulic Controls,
Stage V – ZF EC4 Transmission Control
Unit [FNH856DANZHF01778 – ]