Cubex QXR 1320 10301 Surface Drill Operators Manual

Cubex QXR 1320 10301 Surface Drill Operators Manual

Cubex QXR 1320 10301 Surface Drill Index:

• Section 1 Introduction
  • 1.1 Drill Description
  • 1.2 Manual Objectives
  • 1.3 Drill Orientation
• Section 2 Description of Equipment
  • 2.1 Major Components and Sub-assemblies
    • 2.1.1 Mast and Feed
    • 2.1.2 Frame
      • 2.1.2.1 Inside of Frame
    • 2.1.3 Rear
    • 2.1.4 Operator’s Cab
      • 2.1.4.1 Engine Control Panel
  • 2.2 Electrical Controls
    • 2.2.1 Joysticks
    • 2.2.2 Engine Control Panel (Inside Cab)
  • 2.3 Manual Hydraulic Controls
    • 2.3.1 Set-Up, Drilling, and Tramming Valve Bank
    • 2.3.2 Carousel and Drilling Valve Bank
  • 2.4 Display Screens
    • 2.4.1 System Screen
    • 2.4.2 Status Bar
    • 2.4.3 Menu Buttons
    • 2.4.4 Status Indicator
    • 2.4.5 QXR Shutdowns and Warnings
    • 2.4.6 Configuration Menu
      • 2.4.6.1 Tram Settings
      • 2.4.6.2 Make-up / Breakout Settings
      • 2.4.6.3 Weight on Bit Settings
      • 2.4.6.4 Hourmeter Settings
      • 2.4.6.5 Accra-Feed Configuration Settings
      • 2.4.6.6 Lube/Grease/Water Configuration Settings
      • 2.4.6.7 Pre-set Configuration – Setting Hole Depth
      • 2.4.6.8 Miscellaneous Settings
      • 2.4.6.9 Diagnostic Screen
    • 2.4.7 Tramming and Oscillation
    • 2.4.8 Set-up Screens
      • Set-up Screen – Layer 1
      • Set-up Screen – Layer 2
      • Set-up Screen – Layer 3
    • 2.4.9 Drill Screens
      • Drill Screen – Layer 1
      • Drill Screen – Layer 2
      • Drill Screen – Layer 3
      • Drill Screen – Manual Drilling Layer 1
    • 2.4.10 Accra-Feed Screen – Layer 1
  • 2.5 Software Upgrades
    • 2.5.1 Installing Vansco Software onto a Laptop
      • 2.5.1.1 Basic Qualifications
      • 2.5.1.2 Procedure
    • 2.5.2 Installing Software into the QXR
      • 2.5.2.1 Basic Qualifications
      • 2.5.2.2 Program Systems on the QXR
      • ERIS
      • Vansco
      • 2.5.2.3 Tool List
      • 2.5.2.4 Pre-Installation
      • 2.5.2.5 Accessing the Cab Control Panel
      • 2.5.2.6 Connecting the Keyboard to the CCSystems Computer
      • 2.5.2.7 Loading ERIS Software into the Cubex QXR Drill
      • 2.5.2.8 Connecting a Laptop to the Vansco System
      • 2.5.2.9 Loading Vansco Programs on your Cubex QXR Drill
• Section 3 Start-Up and Tramming
  • 3.1 Operating Procedures for Start-Up
    • 3.1.1 Pre-start Inspection
    • QXR Operator Pre-Start Checklist
  • 3.2 Start-Up
    • 3.2.1 Inside Cab
    • 3.2.2 Outside Cab
  • 3.3 Tramming
    • 3.3.1 Tramming from the Tram Station
    • 3.3.2 Tramming from the Cab
    • 3.3.3 Tramming Stability
  • 3.4 Set-up
    • 3.4.1 Set-Up from the Cab
    • 3.4.2 Indexing the Swing Cylinder
  • 3.5 Shutdown Procedure
  • 3.6 Towing
    • 3.6.1 Towing Guidelines and Precautions
    • 3.6.2 Tow Disconnect – Sun Gear Removal Procedure
    • 3.6.3 Sun Gear Re-install
• Section 4 Drilling
  • 4.1 Drilling Procedures
    • 4.1.1 Hammer Installation Procedure
    • 4.1.2 Drill Pipe Installation (Adding Rods)
    • 4.1.3 Drill Pipe Removal
  • 4.2 Delivery Systems
    • 4.2.1 Water Injection Procedure
    • 4.2.2 Grease Injection Procedure
    • 4.2.3 Oil Injection Procedure
  • 4.3 Drilling
    • 4.3.1 Manual Drilling
    • 4.3.2 Drilling with Accra-Feed Feature (Optional)
• Section 5 Maintenance and Safety
  • 5.1 Daily Maintenance Procedures
    • Safety Instructions for Servicing
      • REMEMBER
      • Fluid Notices
  • 5.2 Lubrication
    • 5.2.1 Rock Drill Grease
    • 5.2.2 Lubrication Points and Intervals
    • 5.2.3 Automatic Machine Lubrication
  • 5.3 Safety Procedures
    • 5.3.1 Personal Protection Equipment
    • 5.3.2 Overhead and Buried Utilities
    • 5.3.3 Ask for Assistance
    • 5.3.4 Safety Shutdowns
    • 5.3.5 Safety Labels
    • 5.3.6 General Safety and Maintenance Instructions
• Section 6 Troubleshooting
  • 6.1 Troubleshooting the Tram Drive
    • Crawler Does Not Run but Tramming Motors Are Operating
    • Crawler Does Not Move and Tramming Motor Does Not Run
    • Crawler Does Not Tram Straight
  • 6.2 Troubleshooting the Hydraulic System
    • Pump Does Not Deliver Oil
    • Pump is Running Hot
    • Cavitation or Pump Noise
    • Insufficient Pressure
    • Slow Rotation at Top Drive
    • No Rotation at Top Drive Assembly
    • Slow or No Feed
    • Mast Does Not Rotate
    • Actuator Allows Mast to Move after Being Set
  • 6.3 Troubleshooting the Water Injection Pump
    • Discharge Pressure is Too Low
    • Cavitation Problems
    • No Water Discharge
    • Excessive Pump Noise
  • 6.4 Troubleshooting the Air Driven Oil Injection Pump
    • Air Motor Does Not Operate
    • Air Seepage from Air Exhaust While Pump is Not Working
    • Loss of Pressure, Volume, or Continuous Operation of Pump when Not in Normal Use
    • Excessive Amount of Air in Lubricant or Excessive Amount of Lubricant in Air
  • 6.5 Troubleshooting the Air Driven Grease Injection
    • Air Motor Does Not Operate
    • Grease Is Not Delivered to the Drilling Air Line
  • 6.6 Troubleshooting the Air Delivery System
    • Air Pressure Builds too Slowly
    • Compressor Shuts Down with Air Demand Present
    • Compressor Does Not Build-Up Full Discharge Pressure
    • Compressor Unloading with an Excessive Pressure Build-Up
    • Excessive Compressor Fluid Consumption
    • Compressor Overheating
  • 6.7 Troubleshooting the Hammer
    • Tool Does Not Start
    • Tool Stops Operating
    • Operating Pressure is Lower than Specifications
    • Low Penetration Rate
    • Galling of Internal Parts
  • 6.8 Troubleshooting the Drill Bit
    • Abrasive Wear
    • Loss of Carbides in Bit
    • Bit Breakage and Carbide Failure
    • Carbide Breakage
    • Uneven Wear Conditions
  • 6.9 Troubleshooting Depth Laser
    • Laser appears not working. No red light is coming out of aperture.
    • Laser appears working, red light is pulsing in even intervals, no output signal.
    • Laser appears working, red light is pulsing but in uneven intervals
    • General notes:
• Cubex Terra DGS Operation Manual
• Section 1 Introduction
  • 1.1 Features
• Section 2 Software Removal and Installation
  • 2.1 Removal / Installation Procedure:
  • 2.2 Sensor Installation
    • 2.2.1 Installing Wires in Sensor Box
    • 2.2.2 Screen Installation
• Section 3 Operation
  • 3.1 ZERO-OFFSET Calibration Procedure
  • 3.2 Local and Absolute Heading Measurements

Cubex