Link Belt LS2700 C Series 2 Excavator Operators Manual

Link Belt LS2700 C Series 2 Excavator Operators Manual

Link Belt LS2700 C Series 2 Excavator Index:

• PREFACE
• CAUTION
• CONTENTS
• OPERATION
  • Safety
    • Before Moving to the Job Site
    • When Machine is Moved to the Job Site
    • Operating Practices
    • During Operation
    • During Traveling
    • On Completion of Daily Operations
    • Standard Hand Signals for Controlling Crawler Excavator Operations
  • Location of Components
  • Hydraulic System
    • Hydraulic Actuator
    • Hydraulic Circuit
  • Electric Circuit
  • Instruments and Controls
    • Starter Switch
    • Off
    • On
    • Start
    • Heat
    • Throttle Dial
    • Lamp Check/Buzzer Stop Switch
    • Heater Switch
    • Swing Lock…Safety Device
    • Cab Light Switch
    • Control Switch…Safety Device
    • Light Switch
    • Travel Caution Buzzer
    • Wiper Switch
    • Horn Switch
    • Mode Select Switch
    • Idle/F Sel Switch
    • Manual Throttle Switch
    • Free Swing Switch
    • Travel Switch
    • Attachment Control Switch (Arm)
    • Travel Lever
    • Operation Levers
    • Front Window
    • Operator’s Seat
    • Console Box
    • SCM Monitor (Systems Control Monitor)
    • Service Monitor
    • Mechanical Control Monitors
    • Swing Parking Brake
  • Operation Modes
    • Load Modes
    • Fine Control Modes
    • Free Swing
  • One Touch Idle and Switch Operation
    • One Touch Idle
    • Switch Operations
  • Switch Malfunction and Redundant (Back-Up)[Emergenty by pass function]
    • Redundant (Back-up)
  • Replacement of Fuse
  • Heater
    • Operation
  • Radio
    • Cautions for Use
    • How to Tune to a Desired Station
  • Battery
    • Cautions for Battery Charging
    • Installation and Removal of Battery
• OPERATING INSTRUCTIONS
  • Cautions for Use of New Machine
  • Engine
    • Before Starting
    • Starting the Machine
    • Stopping the Engine
    • Emergency Engine Stops
  • Warm-Up Operation
    • Warm-Up Procedure
  • Cautions for Operation
    • Operating During the Winter or in Cold Climates
  • Operations
  • Pulling Out From Soft Ground
  • Adjusting Bucket Play
    • Adjustment Methods
  • Turning Over and Replacement of Bucket
  • Bucket Tooth Replacement
  • Operating in Cold Climates
    • Fuel and Lubricant
    • Battery
    • Anti-Freeze Mixing
    • Flushing Procedure
    • Add Anti-Freeze of Proper Density
    • Cautions After Operation
    • When the weather Gets Warmer
  • Transportation
    • Loading
    • Trailer Loading
    • Cautions for Removing of Front Attachment
  • Storage
• INSPECTION AND MAINTENANCE
  • General Cautions for Inspection
  • Caution for Inspection
  • Lubrication Chart
    • Oil Level Check for Take-Up Roller, Upper Roller and Lower Roller
  • Inspection and Maintenance Check List
  • Periodic Maintenance
    • Before Work Inspection
    • Every 50 Hour Maintenance
    • Every 100 Hour Maintenance
    • 60 Hours for the First Time
    • Every 250 Hours Maintenance
    • Every 500 Hours Maintenance
  • Irregular Maintenance
    • Cleaning and Replacement of the Air Cleaner
    • Replacing Coolant
    • Checking and Adjustment of the Track Tension
  • Inspections
  • Measuring Pressure
    • Accumulator Gas Pressure Verification
    • Hydraulic System Relief Valve Adjustment
    • Pilot Circuit Pressure
    • Travel Circuit Pressure
    • Swing Cross Over Relief Pressure
    • Main Control Valve Port Relief Pressures
    • Main Relief Pressure
  • Troubleshooting
    • Main Body
  • Replacement Parts
  • Fuel and Lubricants Per Ambient Temperatures
    • Fuel, Oil
    • Anti-Freeze
  • Hour Meter
  • Who to Contact for Problems
  • Special Attachments
    • Hydraulic Hammer Attachment
    • Extended Service Life of Machine

Link Belt