A TM-35100-1 is a truck crane: it drives to site on its carrier, sets up on outriggers, and lifts with a telescoping boom. When one of these is down in your yard, the person with the wrench needs more than an operator's view of the machine. The service manual is what a fleet mechanic or in-house shop opens to find adjustment procedures, test points and troubleshooting steps before pulling a component.
What this manual helps you do
- Troubleshoot the hydraulic power generating system, from pump output to the circuits it feeds.
- Adjust and check the outrigger, swing, boom elevating, winch and telescoping systems after a repair.
- Diagnose control system and radio control faults by following the system logic.
- Verify safety system function after work on the boom or controls.
- Trace circuits using the system diagrams, and look up values in the data, adjustment and checks section.
Who this is for
A rental fleet mechanic or crane service technician who is repairing a TM-35100-1 in-house. It also suits an independent repair shop that has taken on one of these cranes, or a used unit that arrived with no paperwork.
FAQ
Q: What do I receive and how is it organised?
A: You get the set: 2 PDF files, 448 pages in total, in English. The main manual is Publication TM-35100-1-S1(U)-1E (321 pages), and the second is Publication W301-0361E (127 pages). The text is searchable, so you can jump straight to a fault or a component.
Q: Which machine and serial numbers does it fit?
A: The main manual is for the Tadano TM-35100-1, serial number 291072 and up. Publication W301-0361E is marked for serial numbers 291067 and up, 291072 and up. Check your carrier's plate against those numbers.
Q: How does it fit the job I'm doing?
A: The sections run by system, with hydraulic power generating, outriggers, swing, boom elevating, winch, telescoping, safety, control and radio control, followed by data, adjustment and checks and system diagrams. You can go from symptom to system to procedure without hunting.
Keep it on the shop computer or a tablet at the crane, and the next repair starts with the procedure in front of you, not guesswork.
Click here to view the preview (PDF)
Does this manual fit your machine?
| Model |
Serial No. |
| TM-35100-1 |
291072 and up |
The serial number shown is the one printed on the manual cover. Check the model and serial number on your machine's data plate before ordering.
📘 Show Index
Table of Contents:
- Publication TM-35100-1-S1(U)-1E / Serial No. 291072 and up (321 pages)
- Foreword
- Applicable spec. No
- Separate service manual
- Outline of specifications
- (B) Hydraulic Power Generating System
- B-1 Hydraulic Power Generating System
- B-2 Hydraulic Pump
- B-3 Solenoid Control Valve (Outrigger)
- (C) Outrigger System
- C-1 Outrigger System
- C-2 Jack Cylinder
- C-3 Pilot check Valve (Jack Cylinder Retracting Prevention)
- (D) Swing System
- D-1 Swing System
- D-2 Swing Assembly
- D-3 Hydraulic Pilot Control Valve (Swing)
- (E) Boom Elevating System
- E-1 Elevating System
- E-2 Elevating Cylinder
- E-3 Counterbalance Valve (Elevating)
- (F) Winch System
- F-1 Winch System
- F-2 Winch
- F-3 Hydraulic Motor and Counterbalance Valve
- (G) Telescoping System
- G-1 Telescoping System
- G-2 Boom (Four-Section Boom)
- G-4 Telescoping Cylinder
- (H) Safety System
- H-1 Safety System
- H-2 Boom Length and Angle Detector
- H-3 Outrigger Extension Length Detector
- (L) Control System
- L-1 Control System
- L-2 Remote Control Valve (Lever)
- L-3 Remote Control Valve (Pedal)
- (V) Radio Control System
- V-1 Configurations of Radio-control System
- V-2 Radio-control Valve
- V-3 Acclerator Cylinder
- (Y) Data, Adjustment and Checks
- Y-1 Hydraulic Pressure Setting Table
- Y-2 Air Bleeding Procedure
- Y-3 Electric Switch Adjustment
- (Z) System Diagrams
- Z-1 Hydraulic Circuit
- Z-2 Electric Circuit
- Z-3 Location of Hydraulic Parts (Upper)
- History of revision
- Publication W301-0361E / Serial No. 291067 and up, 291072 and up (127 pages)
- Foreword
- Components of the AML Main Unit
- Panel
- Internal view and name plate
- Internal block diagram
- Diagram of the AML System (GS-300-1)
- Input/Output Signals of the AML System (GS-300-1)
- Diagram of the AML System (TM-3500-1)
- Input/Output Signals of the AML System (TM-3500-1)
- [OPERATION]
- Functions of and How to Use User Mode (GS-300-1)
- Mode Structure
- Configuration and Functions of theAML System
- Names and Functions of AML Main Unit Parts
- Functions of and How to Use User Mode (TM-3500-1)
- Mode Structure
- Configuration and Functions of theAML System
- Names and Functions of AML Main Unit Parts
- [ADJUSTMENT AND MAINTENANCE]
- General: Adjustment Mode and Maintenance Mode
- Keys and Switches for Adjustment and Maintenance
- Mode Structure and Menu
- Method of Shifting Modes
- Required Adjustment After AML System Parts Replacement
- Functions of and How to Use Adjustment Mode
- Adjustment Procedures
- Adjustment Initialization
- Capacity Setting
- Functions of and How to Use Maintenance Mode
- Program Version Display
- Data ID Number Display
- Di Check
- Error Message
- Display of Error Message
- How to Read the Error Message
- How to Read the Error History
- [INFORMATION AND DATA]
- Checking the Detectors(GS-300-1)
- Boom Length Detector
- Boom Angle Detector
- Swing Angle Detector
- Checking the Detectors(TM-3500-1)
- Boom Length Detector
- Boom Angle Detector
- Swing Angle Detector
- Fuses
- Replacing the Clock Battery
- History of revision
Tadano PDF Manuals
All Crane Manuals
