$ 0
0
$ 0
0

Mustang 2056 Skid Steer Loader Operator Manual (50950014A)

Format: PDF (Printable Document)

File Language: English

File Size: 1.95 MB (Speed Download Link)

Brand: Mustang

Model: 2056

Machine Type: Skid Steer Loader

Publication No.: 50950014 (Rev. A)

Edition Date: August 2011

Serial No.: SN 003301 and Up

Type of Document: Operator Manual (operation, controls, safety and routine maintenance)

Searchable: Yes, text is searchable and copyable

Delivery: Instant download after payment

Categories: ,

$ 40

Share:

Mustang 2056 Skid Steer Loader Operator Manual (50950014A)

Publication 50950014, Rev. A, edition date August 2011, covers the Mustang 2056 skid steer loader from serial number 003301 and up. It is the operator's book for that machine, written in English.

If you have taken in a 2056 without its book, or you are handing one to a new operator or a rental customer, this is the manual to put in the cab. It opens with Introduction, Loader Identification and the control and indicator symbols, then goes through safety, controls and the equipment that comes with the machine.

What this manual helps you do

  • Start with the Mandatory Safety Shutdown Procedure and the Safety Reminders, so every new operator hears the same rules.
  • Operate the machine from the Hand/Foot Controls, Drive Controls, Lift/Tilt Controls and Dual-Hand Controls sections, plus Engine Speed Control and the optional Two-Speed Transmission and Hydraglide ride control.
  • Check the Safety Interlock System, Operator Restraint Bar, Upper-Torso Restraint, Parking Brake and Lift Arm Support Device against the descriptions in Controls and Safety Equipment.
  • Look up Engine Oil, Engine Oil Filter and Engine Oil Pressure, and the Maintenance Log for recording service.
  • Adjust chain tension by following the Adjusting Chain Tension steps, and read the Engine Diagnostic Chart and Troubleshooting section when the loader does not behave.

Who this is for

Best for a dealer or contractor who gets a 2056 ready for the next operator, and for an owner-operator who bought one used without the book. It also suits rental fleets that want the safety decals, controls and daily checks documented for each customer.

Print the Maintenance Log page and keep it with the machine.

Preview of the Mustang 2056 Skid Steer Loader Operator Manual (50950014A) (PDF, sample pages)

Does this manual fit your machine?

Mustang model 2056
Machine type Skid Steer Loader
Publication No. 50950014 (Rev. A)
Edition date August 2011
Serial numbers SN 003301 and Up

Check the model and serial number on your machine’s serial plate before ordering.

What’s inside

  • Troubleshooting: Engine Diagnostic Chart; Troubleshooting
  • Torque values: Torque Specifications
  • Maintenance intervals / schedule: Maintenance Log
  • Lubrication, oils, fluids and capacities: Engine Oil; Engine Oil Filter; Engine Oil Pressure
  • Technical specifications: Specifications; Loader Specifications; Dimensional Specifications
  • Adjustments and calibration: Adjustments; Adjusting Chain Tension

How this edition differs

Compared with Mustang 2056 Skid Steer Loader Operator Manual (917402D):

This manual Other edition
Publication No. 50950014A 917402D
Edition date August 2011 March 2010

FAQ

Where do I find the safety decals?
The Safety Decals section shows ANSI-style and ISO-style decals, both inside the ROPS/FOPS and in the engine compartment. Product and Component Plate Locations shows where the plates are.

Does it include torque values and specifications?
Yes. Torque Specifications is a section of its own, and Specifications is split into Loader Specifications and Dimensional Specifications.

What is the difference from manual 917402D?
917402D is an earlier edition of the 2056 operator manual, dated March 2010. This one is 50950014A, dated August 2011, and covers serial number 003301 and up.

Which section covers the optional equipment?
The optional Heater, Heater and Air Conditioner, Two-Speed Transmission and Hydraglide Ride Control System each have their own heading in Controls and Safety Equipment. Attachment Mounting is listed there too.

📘 Show Index

Table of Contents:

  • Hand/Foot Controls
    • Drive Controls
    • Lift/Tilt Controls
  • Dual-Hand Controls
    • Figure 14 Dual-Hand Controls
    • Drive Controls
    • Lift/Tilt Controls
  • Introduction
    • Loader Identification
    • Control/Indicator Symbols
      • Power Off
      • Power On
      • Engine Start
      • Battery Charge
      • Electrical Power
      • Worklight w/Flasher
      • Worklight
      • Safety Alert
      • Hazard Flasher
      • Seatbelt
      • Horn
      • Volume – Full
      • Volume – Half Full
      • Volume – Empty
      • H-L
      • High – Low
      • Neutral
      • Forward
      • Reverse
      • Parking Brake
      • Engine Air Filter
      • Engine Oil
      • Engine Oil Filter
      • Engine Oil Pressure
      • Fuel Filter
      • Engine Temperature
      • Hydraulic System
      • Hydraulic Oil Temperature
      • Hydraulic Oil Filter
      • Grease Lubrication Point
      • Glow Indicator Lamp
      • Diesel Fuel
      • Chaincase Oil
      • Clockwise Rotation
      • Counterclockwise Rotation
      • Fast Speed
      • Slow Speed
      • Ride Control
      • Power-A-Tach®
      • Bucket – Float
      • Bucket – Rollback
      • Bucket – Dump
      • Lift Arm – Lower
      • Lift Arm – Raise
      • Service Hours
      • Lift Point
      • Tie-Down Point
      • Diesel Water Separator
      • Engine Malfunction Shutdown
  • Safety
    • Mandatory Safety Shutdown Procedure
    • Safety Reminders
    • Potential Hazards
    • Safety Decals
      • New Decal Application
    • ANSI-Style Safety Decals inside the ROPS/FOPS
    • ANSI-Style Safety Decals in the Engine Compartment
    • ISO-Style (used Internationally) Safety Decals inside the ROPS/FOPS
    • ISO-Style (used Internationally) Safety Decals in the Engine Compartment
    • Product and Component Plate Locations
  • Controls and Safety Equipment
    • Guards and Shields
    • Operator Restraint Bar
    • Operator’s Seat
      • Figure 1 Operator’s Seat
    • Upper-Torso Restraint
    • Safety Interlock System
      • Hydraloc™ System
      • Testing the Safety Interlock System
    • ROPS/FOPS
    • Parking Brake
      • Figure 2 Parking Brake Switch
    • Horn
    • Rear Window Emergency Exit
    • Lift Arm Support Device
      • Engagement
        • Figure 3 Lift Arm Support Device Engaged
      • Disengagement
        • Figure 4 Lift Arm Support Device Storage Location
    • Accessory Plug
    • Dome Light
    • Work Lights
    • Heater (optional)
    • Heater and Air Conditioner (optional)
      • Figure 5 Heater/ Air Conditioner Controls
    • Tips For Improving Heater Performance
    • Engine Speed Control
      • Figure 6 Hand Throttle
      • Figure 7 Foot Throttle
    • Two-Speed Transmission (optional)
    • Hydraglide™ Ride Control System (optional)
    • Auto-Shutdown System
    • Attachment Mounting
      • Multi-Tach™ Hitch
        • Figure 8 Multi-Tach™ Hitch
      • Power-A-Tach® Hitch
        • Figure 9 Power-A-Tach® Hitch
    • Instrument Panels
      • Figure 10 Left Panel
      • Left Panel
      • Right Panel
        • Figure 11 Right Panel
    • Dual Joystick Controls
      • Figure 12 Joystick Controls
      • Drive Control
      • Lift/Tilt Control
    • Auxiliary Hydraulic System
      • Standard-Flow Auxiliary Hydraulic Control
        • Figure 16 Dual Joystick Electric Auxiliary Control
        • Figure 17 Hand/Foot Auxiliary Control
      • High-Flow Auxiliary Hydraulic Control (optional)
        • Figure 18 High-Flow Auxiliary Switch
  • Operation
    • Before Starting the Engine
    • Starting the Engine
    • Cold-Starting
    • Cold-Starting Procedure
    • Stopping the Loader
    • Parking the Loader
    • Jump-Starting
    • Changing Attachments
      • Connecting Attachments
        • Figure 19 Manual Hitch – disengaged
        • Figure 20 Power Hitch – disengaged
      • Connecting Auxiliary Hydraulic Couplings
      • Removing an Attachment
    • Self-Leveling
    • Using a Bucket
      • Driving Over Rough Terrain
      • Driving On an Incline
      • Digging with a Bucket
        • Figure 21 Digging
      • Loading a Bucket
        • Figure 22 Loading
      • Dumping the Load Onto a Pile
        • Figure 23 Dumping into a Truck or Hopper
      • Dumping the Load Over an Embankment
      • Scraping with a Bucket
        • Figure 24 Scraping
      • Leveling the Ground
        • Figure 25 Leveling the Ground
    • Vibration Information
    • Vibration Measurement and Actions
      • Vibration Levels
        • Figure 26 Vibration measurement axes
    • Highway Travel
    • Storing the Loader
    • Removing Loader from Storage
    • Transporting the Loader
      • Figure 27 Front Tie-Down/ Retrieval Points
        • Figure 28 Rear Tie-Down/ Retrieval Points
    • Lifting the Loader
      • Figure 29 Single-Point Lift Eye
        • Figure 30 Front Four-Point Lift Eyes
        • Figure 31 Right Rear Four-Point Lift Eye (left same)
  • Service
    • Dealer Services
    • Replacement Parts
    • Loader Raising Procedure
      • Figure 32 Loader Properly Blocked (Tires and wheels removed to show blocks)
    • Loader Lowering Procedure
    • Engine Compartment Access
      • Figure 33 Engine Compartment Access Doors
    • Tilting Back the ROPS/FOPS
      • Figure 34 ROPS/FOPS Lock Mechanism – Engaged
    • Adjustments
      • Control Handles
      • Fuel Sender
    • Foreign Material Removal
    • Lubrication
      • Figure 35 Service Locations
    • Chaincases
      • Checking and Adding Oil
        • Figure 36 Fill and Check Plug Location
      • Draining Oil
        • Figure 37 Drain Plug
    • Drive Chains
      • Checking Chain Tension
      • Adjusting Chain Tension
    • Engine Air Cleaner
      • Figure 38 Dual-Element Air Cleaner
      • Changing the Air Cleaner Elements
      • Outer Element
      • Inner Element
      • Reinstallation
    • Engine Service
      • Checking Engine Mounting Hardware
      • Checking Engine Oil Level
        • Figure 39 Engine Service Components
      • Changing Engine Oil and Filter
        • Figure 40 Remote Engine Oil Drain
      • Changing Main Fuel Filter
    • Engine Diagnostic Chart
      • Figure 41 Flashing Patterns of the Failure Lamp
    • Hydraulic System
      • Checking Hydraulic Oil Level
        • Figure 42 Sight Gauge and Fill Tube
      • Changing Hydraulic Oil Filter
        • Figure 43 Hydraulic Oil Filter and Indicator
      • Changing Hydraulic Oil
    • Bucket Cutting Edge
    • Alternator/Fan Belt
    • Wheel Nuts
    • Lift Arm Pivots
    • Cooling System
      • Cleaning the Cooling System
    • Tires
      • Checking Tire Pressure
    • Heater Filters
    • Electrical System
      • Fuse Panel
      • Battery
  • Troubleshooting
  • Maintenance
    • Maintenance Log
  • Specifications
    • Loader Specifications
    • Standard Features
    • Optional Features
    • Dimensional Specifications
      • 15.1 ft.3 (0.43 m3) Bucket w/12 x 16.5 Tires inches mm
    • Capacities and Ratings
      • 2056 Models
        • (186 kg)
        • (198 kg)
        • (154 kg)
        • (200 kg)
        • (227 kg)
        • (227 kg)
        • (227 kg)
    • Common Materials and Densities
    • Bucket Selection
  • Torque Specifications
  • WARRANTY
    • MUSTANG WARRANTY SERVICE INCLUDES
    • MUSTANG WARRANTY DOES NOT INCLUDE
  • INDEX

Mustang PDF Manuals

Related Manuals

0
0
Your Cart
Your cart is emptyReturn to Shop