A CT2035 compact tractor is the kind of machine you use to mow, move round bales, run an auger, or pull a box blade around the place. When something starts leaking, grinding, or just quits moving, this is the book the mechanic or hands-on owner pulls out. You use it when you're past guesswork and you need specs, test ports, wiring info, and step-by-step teardown so the tractor is back working by Monday.
What this manual helps you do
- Diagnose no-start, hard-start, or low-power issues on the small diesel engine and fuel system
- Trace and repair electrical problems using wiring diagrams and connector callouts
- Check and adjust hydrostatic and hydraulic system pressures with the right test ports and procedures
- Follow step-by-step removal and installation of axles, 3-point components, steering, and driveline parts
- Rebuild or reseal cylinders, valves, and other hydraulic components with proper assembly order and checks
Who this is for
This manual is for CT2035 owners, small contractors, farm shops, and field techs who are actually tearing into the tractor and need repair procedures and specs. If you just want to learn controls, service intervals, or basic maintenance, you want the operator's handbook instead, not this service manual.
FAQ
Q: Is this a searchable PDF, and can I read the wiring diagrams clearly?
A: Yes, it's a PDF you can search by keyword, and the wiring diagrams are sized so you can zoom in and read pin numbers and wire colors.
Q: How do I know if it fits my tractor's serial number?
A: It's written for CT2035 tractors in the B4ZF11001 through B4ZF99999 serial number range. If your plate falls in there, this is the right one.
Q: Is this the right manual if I'm doing my own repairs?
A: Yes, if you're doing real repair work beyond basic service, this is the workshop manual you want.
Bottom line: If you own or work on a CT2035 in that serial range and plan to wrench on it yourself, this is the correct manual. If you only need operating tips, it's overkill.
📘 Show Index
Table of Contents:
- FORWARD
- TABLE OF CONTENTS
- SAFETY FIRST
- FOR SAFETY
- SAFETY TIPS
- SAFETY GEAR
- WORK PLACE
- SAFETY INSTRUCTIONS WHEN PREPARING TRACTOR
- AVOID FIRES
- CAUTIONS WHEN HANDLING THE BATTERY
- CAUTIONS FOR HIGH PRESSURE HOSES
- USE OF APPROPRIATE TOOLS AND EQUIPMENT
- HANDLING OF HAZARDOUS MATERIALS
- HANDLING OF ROTATING BLADE, SHAFT AND DRIVING BELT
- PREVENTION OF SCALD
- DISPOSAL OF ENVIRONMENTAL WASTE
- CAUTIONS WHEN HANDLING TIRES
- SAFETY DECALS
- GENERAL
- DESCRIPTION FOR SYMBOLS AND ABBREVIATIONS
- TRACTOR EXTERIOR VIEW
- IDENTIFICATION NUMBER
- ENGINE SERIAL NUMBER
- TRANSMISSION SERIAL NUMBER
- DIMENSIONS
- SPECIFICATIONS
- DRIVING SPEED
- ARRANGEMENT OF MAIN SHIFT GEAR AND REAR AXLE GEARS
- MAINTENANCE
- TIGHTENING TORQUE
- GENERAL USE SCREWS, BOLTS, AND NUTS
- STUD BOLTS
- AMERICAN STANDARD SCREWS, BOLTS AND NUTS WITH UNC OR UNF THREADS
- SPRING PIN AND SNAP RING INSTALLATION
- SPRING PIN TYPE
- SNAP RING INSTALLATION
- UNIT CONVERSION TABLE
- ENGINE
- ENGINE IDENTIFICATION
- ENGINE DECAL (A)
- ENGINE NUMBER (B)
- SPECIFICATIONS
- GENERAL SPECIFICATIONS
- ENGINE PERFORMANCE CURVE
- OPERATING PRINCIPLE
- BODY AND POWER TRAIN SYSTEM
- LUBRICATING SYSTEM
- COOLING SYSTEM
- FUEL SYSTEM
- FUEL FILTER
- BLEEDING THE FUEL SYSTEM
- FUEL FEED PUMP
- FUEL INJECTION PUMP
- INJECTION NOZZLE
- GOVERNOR AND STOP SYSTEM
- Basic principle of governor system
- Operation of Governor
- PCV VALVE
- TROUBLESHOOTING
- MEASUREMENT AND ADJUSTMENT
- FAN BELT
- PISTON COMPRESSION PRESSURE MEASUREMENT
- VALVE CLEARANCE
- VALVE LIFT (DEFLECTION AND WORN CONDITION OF VALVE CAM, TAPPET, PUSH ROD, ROCKER ARM, ETC.)
- INJECTION TIMING MEASUREMENT AND ADJUSTMENT
- OIL PRESSURE MEASUREMENT
- BUBBLE TEST FOR RADIATOR
- INJECTION NOZZLE INSPECTION
- EXPLODED VIEW
- CYLINDER BLOCK
- OIL PAN
- CYLINDER HEAD
- GEARCASE
- MAIN BEARING CASE
- VALVE ROCKER ARM
- CYLINDER HEAD COVER
- CAMSHAFT
- PISTON CRANKSHAFT
- FLYWHEEL
- NOZZLE HOLDER
- FUEL CAMSHAFT
- SPEED CONTROL PLATE
- ENGINE STOP LEVER
- GOVERNOR
- WATER PUMP
- WATER HOSE
- ALTERNATOR
- MANIFOLD
- ENGINE DISASSEMBLY AND SERVICING
- PCV VALVE
- HEAD COVER INSTALLATION
- GLOW PLUG AND FUEL OVERFLOW PIPE
- HEAT SEAL REMOVAL
- ROCKER ARM ASSEMBLY
- REMOVAL AND INSTALLATION
- ROCKER ARM ASSEMBLY CHECK
- CYLINDER HEAD
- CYLINDER HEAD REMOVAL
- CYLINDER HEAD INSTALLATION
- CYLINDER HEAD SURFACE FLATNESS CHECK
- INTAKE AND EXHAUST VALVES
- VALVE REMOVAL
- VALVE INSTALLATION
- VALVE RECESS CHECK
- VALVE SEAT CHECK
- VALVE SPRING CHECK
- VALVE SPRING SQUARENESS (TILT)
- INJECTION PUMP
- INJECTION PUMP REMOVAL
- INJECTION PUMP INSTALLATION
- INJECTION PUMP DISASSEMBLY
- NOZZLE HOLDER DISASSEMBLY
- GOVERNOR SPRING AND STOP SOLENOID
- Gearcase
- IDLE GEAR AND CRANK GEAR
- VALVE CAMSHAFT
- FUEL CAMSHAFT
- CRANK GEARS AND SHAFTS CHECK
- TIMING GEAR BACKLASH
- IDLE GEAR SIDE CLEARANCE
- VALVE CAMSHAFT GEAR SIDE CLEARANCE
- FUEL CAMSHAFT GEAR SIDE CLEARANCE
- IDLE GEAR OIL CLEARANCE MEASUREMENT
- IDLE GEAR BUSHING REPLACEMENT
- VALVE CAMSHAFT OIL CLEARANCE MEASUREMENT
- PISTON AND CONNECTING ROD
- VALVE CAMSHAFT DEFLECTION CHECK
- VALVE CAM HEIGHT MEASUREMENT
- PISTON AND CONNECTING ROD CHECK
- PISTON PIN BORE
- PISTON PIN AND BUSHING CLEARANCE
- PISTON PIN BUSHING REPLACEMENT
- PISTON RING MEASUREMENT
- PISTON RING END GAP
- PISTON RING CLEARANCE
- CRANKSHAFT AND FLYWHEEL
- METAL JOURNAL BEARINGS
- FLYWHEEL AND CRANKSHAFT CHECK
- FLYWHEEL DEFLECTION AND CRANKSHAFT END PLAY
- CRANKSHAFT DEFLECTION
- CRANKSHAFT JOURNAL AND BEARING 1 OIL CLEARANCE
- CRANKSHAFT METAL BEARING 1 REPLACEMENT
- CRANKSHAFT JOURNAL AND BEARING 2 OIL CLEARANCE
- CYLINDER BORE CHECK
- CRANK PIN AND CONNECTING ROD BEARING 2 OIL CLEARANCE
- OIL PUMP, OIL FILTER, RELIEF VALVE AND OIL STRAINER
- RELIEF VALVE OF ENGINE OIL
- OIL PUMP CHECK
- THERMOSTAT
- WATER PUMP
- TRANSMISSION
- SPECIFICATIONS
- GENERAL SPECIFICATIONS
- TIGHTENING TORQUE FOR MAJOR COMPONENTS
- SEALANT AND ADHESIVE SPECIFICATIONS
- STRUCTURE AND OPERATING PRINCIPLE
- MAIN GEAR SHIFT SECTION
- OPERATING PRINCIPLE OF SYNCHRONIZER
- RANGE SHIFT SECTION
- PTO GEAR SHIFT SECTION
- FRONT WHEEL DRIVE SECTION
- INSPECTION AND ADJUSTMENT
- SYNCHRONIZER GEAR INSPECTION
- TROUBLESHOOTING
- EXPLODED VIEW
- FRONT DRIVE SYSTEM
- RANGE FORK
- PTO SHIFT FORK
- FRONT DRIVE FORK
- PTO SHAFT
- MAIN SHAFT
- HST PROPER SHAFT
- RANGE SHAFT
- PTO DRIVE SHAFT
- DISASSEMBLY, SERVICE AND ASSEMBLY
- TRANSMISSION CASE MAIN SHIFT, RANGE SHIFT SECTION DISASSEMBLY
- FRONT WHEEL DRIVE SECTION DISASSEMBLY
- TRANSMISSION CASE SHIFT SECTION ASSEMBLY
- PTO SHAFT DISASSEMBLY
- HST [HST MODEL]
- SPECIFICATIONS
- GENERAL SPECIFICATIONS
- HST
- MAJOR TIGHTENING TORQUE
- HST STRUCTURE & COMPONENTS
- OPERATING PRINCIPLE
- STRUCTURE AND FUNCTION OF HST
- BASIC PRINCIPLE OF HST
- FUNCTION HST CHARGE PUMP
- CHARGE RELIEF VALVE
- HIGH PRESSURE RELIEF VALVE
- OPERATION OF HST
- NEUTRAL STATUS
- FORWARD DRIVING
- REVERSE DRIVING
- TROUBLESHOOTING
- MEASUREMENT AND ADJUSTMENT
- CHARGE RELIEF VALVE PRESSURE CHECK
- HP RELIEF VALVE PRESSURE CHECK
- HST PEDAL LINK ADJUSTMENT
- HST PEDAL ADJUSTMENT
- HST NEUTRAL POSITION ADJUSTMENT
- CRUISE MAGNETIC CLEARANCE
ADJUSTMENT (OPTIONAL)
- BLEEDING AIR FROM HST COMPONENT
- EXPLODED VIEW
- TRANSMISSION CASE
- HST ASSY
- HST EXTERNAL HYDRAULIC LINE
- HST PEDAL
- CRUISE (OPTIONAL)
- HST CONTROL
- SERVICING
- HST DISASSEMBLY AND ASSEMBLY
- HST COMPONENTS DISASSEMBLY AND ASSEMBLY
- REAR AXLE
- SPECIFICATIONS
- TRANSMISSION FLUID
- TIGHTENING TORQUES
- OPERATING PRINCIPLE
- PRINCIPLE OF DIFFERENTIAL SYSTEM
- TROUBLESHOOTING
- INSPECTION AND ADJUSTMENT
- BACKLASH FOR DIFFERENTIAL PINION AND SIDE GEAR
- PRELOAD OF TAPER ROLLER BEARING IN DIFF.
- BACKLASH FOR SPIRAL BEVEL PINION AND RING GEAR
- TOOTH CONTACT OF SPIRAL BEVEL
- EXPLODED VIEW
- SPIRAL BEVEL GEAR
- REAR DIFFERENTIAL SYSTEM
- DIFFERENTIALl LOCK FORK
- REAR AXLE
- DISASSEMBLY, SERVICING AND ASSEMBLY
- REAR AXLE COMPONENTS
- REAR DIFFERENTIAL DISASSEMBLY
- REAR DIFFERENTIAL SYSTEM
COMPONENTS DISASSEMBLY
- REAR DIFFERENTIAL SYSTEM ASSEMBLY
- REAR DIFFERENTIAL INSTALLATION
- BRAKE
- SPECIFICATIONS
- STRUCTURE AND OPERATION PRINCIPLE
- TROUBLESHOOTING
- INSPECTION AND ADJUSTMENT
- BRAKE PEDAL FREE PLAY
- CLEARANCE OF BRAKE LAMP SWITCH
- BRAKE PEDAL STOPPER
- BRAKE COMPONENTS INSPECTION
- BRAKE DISC
- BRAKE PLATE
- CAM PLATE
- CAM PLATE AND STEEL BALL
- EXPLODED VIEW
- DISASSEMBLY, SERVICING AND ASSEMBLY
- BRAKE SECTION DISASSEMBLY AND ASSEMBLY
- FRONT AXLE
- SPECIFICATIONS
- GENERAL SPECIFICATIONS
- SEALANT AND ADHESIVE
- TIGHTENING TORQUE FOR MAJOR COMPONENTS
- STRUCTURE AND OPERATING PRINCIPLE
- POWER TRANSFER SYSTEM FOR FRONT AXLE
- DIFFERENTIAL SYSTEM
- LOAD TRANSFER
- TROUBLESHOOTING
- INSPECTION AND ADJUSTMENT
- TOE-IN
- STEERING ANGLE
- SWAY RESISTANCE
- PRELOAD OF TAPER ROLLER BEARING ON SPIRAL BEVEL PINION SHAFT
- BACKLASH FOR DIFFERENTIAL PINION AND DIFFERENTIAL SIDE GEAR
- BACKLASH FOR SPIRAL BEVEL PINION AND 23 SPIRAL BEVEL GEAR
- TOOTH CONTACT OF SPIRAL BEVEL GEAR
- TOOTH CONTACT FOR UPPER BEVEL GEARS AND FINAL DRIVE BEVEL GEARS
- EXPLODED VIEW
- FRONT DIFFERENTIAL
- FRONT AXLE CASE
- FRONT AXLE
- FRONT AXLE BRACKET
- BEVEL PINION SHAFT
- DIFF. GEAR SHAFT
- DISASSEMBLY, SERVICE AND ASSEMBLY
- FRONT AXLE OIL SEAL REPLACEMENT
- BEVEL Gearcase AND FRONT AXLE CASE DISASSEMBLY AND ASSEMBLY
- FRONT DIFFERENTIAL SYSTEM REMOVAL AND INSTALLATION
- FRONT DIFFERENTIAL SYSTEM DISASSEMBLY AND ASSEMBLY COMPONENTS
- STEERING SYSTEM
- SPECIFICATIONS AND TIGHTENING TORQUE
- SPECIFICATIONS FOR STEERING SYSTEM
- TIGHTENING TORQUE FOR MAJOR COMPONENTS
- HYDRAULIC PUMP
- POWER STEERING UNIT
- STEERING CYLINDER
- OPERATING DIAGRAM
- STRUCTURE AND OPERATING PRINCIPLE
- STEERING UNIT
- OPERATING PRINCIPLE
- STRUCTURE AND SPECIFICATIONS
- OPERATING PRINCIPLE OF STEERING SYSTEM
- STRUCTURE AND OPERATING PRINCIPLE
- TROUBLESHOOTING
- INSPECTION AND ADJUSTMENT
- EXPLODED VIEW
- STEERING CYLINDER
- POWER STEERING CYLINDER
- STEERING COLUMN
- DISASSEMBLY, SERVICE AND ASSEMBLY
- STEERING UNIT (ORBITROL UNIT) COMPONENTS DISASSEMBLY
- STEERING UNIT COMPONENTS ASSEMBLY
- STEERING CYLINDER REMOVAL
- RELIEF VALVE DISASSEMBLY AND ASSEMBLY
- HYDRAULIC SYSTEM
- SPECIFICATIONS
- GENERAL SPECIFICATIONS
- TIGHTENING TORQUE
- STRUCTURE AND OPERATING PRINCIPLE
- COMPONENT ARRANGEMENT
- OPERATING PRINCIPLE
- OPERATING DIAGRAM
- IMPLEMENT SECTION
- MAIN SECTION
- HYDRAULIC FILTER
- HST FILTER [HST MODEL]
- COMPONENTS
- GEAR PUMP
- REAR AUX. VALVE (REMOTE HYDRAULIC VALVE)
- LIFT CONTROL VALVE (PCV VALVE)
- HYDRAULIC BLOCK
- LOADER JOYSTICK VALVE
- OIL COOLER [HST MODEL]
- HYDRAULIC LIFT CYLINDER
- TROUBLESHOOTING
- INSPECTION AND ADJUSTMENT
- LEVER SETTING OF HYDRAULIC LIFT CYLINDER
- PRE-INSPECTION
- ADJUSTING THE POSITION CONTROL LEVER
- SETTING THE JOYSTICK LEVER
- HYD. CYLINDER
- EXPLODED VIEW
- LIFT CONTROL VALVE
- HYDRAULIC 1
- HYDRAULIC 2
- EXTERNAL HYDRAULIC VALVE
- HYDRAULIC BLOCK (T3)
- SUCTION PIPE GROUP (T4)
- GEAR PUMP
- DISASSEMBLY, SERVICE AND ASSEMBLY
- DISASSEMBLY OF GEAR PUMP
- GEAR PUMP ASSEMBLY
Components Assemby
- AUX. HYDRAULIC VALVE (DOUBLE ACTING VALVE)
- HYDRAULIC CYLINDER
- HYDRAULIC CYLINDER ASSEMBLY DISASSEMBLY
- HYDRAULIC CYLINDER ASSEMBLY REASSEMBLY
- LIFT CONTROL VALVE
- FLOW CONTROL VALVE
- RELIEF VALVE
- HYDRAULIC BLOCK
- HYDRAULIC BLOCK ASSEMBLY
COMPONENTS DISASSEMBLY
- LOADER JOYSTICK VALVE
- ELECTRIC SYSTEM
AND DIAGNOSIS
- SPECIFICATIONS
- WIRING IDENTIFICATION
- CROSS SECTIONAL AREA OF WIRING
- SYMBOLS FOR ELECTRIC COMPONENTS
- FUSE
- INSPECTION
- CAUSE FOR BLOWN FUSE
- ELECTRIC DEVICE DIAGNOSIS
- OPERATING PRINCIPLE
- WHEN IGNITION SWITCH IS TURNED TO "ACC" POSITION
- OPERATING PRINCIPLE OF PREHEAT
- WHEN IGNITION SWITCH IS TURNED TO "ST" POSITION
- CHARGE WARNING LAMP OPERATION
- ECU OPERATION
- ELECTRIC COMPONENTS
- SLOW-BLOW FUSE
- IGNITION SWITCH
- IGNITION SWITCH OPERATION
- KEY SWITCH TEST
- START MOTOR
- ALTERNATOR
- COMBINATION SWITCH
- FLASHER UNIT
- GLOW RELAY
- FUSE & RELAY BOX
- GLOW PLUG
- MICRO 5P RELAY
- MICRO 4P RELAY
- COOLANT TEMPERATURE SENSOR
- ENGINE STOP SOLENOID
- ENGINE OIL PRESSURE SWITCH
- PICKUP SENSOR
- FUEL SENDER
- HAZARD WARNING LAMP SWITCH
- SENSORS AND RELAYS
- CRANKSHAFT WHEEL SENSOR
- WATER-IN-FUEL SENSOR
- BRAKE SWITCH
- PARKING BRAKE MICRO SWITCH
- SAFETY START SWITCH
- ONE SIDE BRAKE SWITCH
- PTO SAFETY SWITCH
- SWITCHS
- CRUISE SWITCH [HST MODEL: OPTIONAL]
- LINKED PEDAL SWITCH
- PREHEAT CONTROLLER
- SEAT SWITCH
- INSTRUMENT PANEL
- SYBOMLS AND COMPONENTS
- CONNECTOR
- GAUGES AND INDICATORS
- LAMPS
- HEADLAMP
- FRONT COMBINATION LAMP
- WORK LAMP
- REAR COMBINATION LAMP
- TROUBLESHOOTING
- WHEN THE ENGINE CANNOT BE STARTED
- WHEN THE SYSTEM IS NOT CHARGED
- WHEN THE SYSTEM IS NOT PREHEATED MANUALLY
- WHEN THE SYSTEM IS NOT PREHEATED AUTOMATICALLY
- WHEN THE HEAD LAMP CANNOT BE OPERATED
- FUEL GAUGE OPERATION
- TEMPERATURE GAUGE OPERATION
- TACHOMETER OPERATION WITH THE ENGINE RUNNING
- HOUR METER OPERATION
- EXPLODED VIEW
- ENGINE ELECTRICAL
- START CONTROL
- LIGHT CONTROL
- WIRE HARNESS
- DISPLAY CONTROL
- ENGINE ELECTRICAL (3)
- GLOW CONTROL
- FUEL SENDER
- PTO CONTROL
- DIAGNOSIS
- INDEX
- 1.1 ALERT SYMBOLS
- 6.18 ALTERNATOR
- 4.4 ALTERNATOR
- 8.3 AMERICAN STANDARD SCREWS, BOLTS AND NUTS WITH UNC OR UNF THREADS
- 1.3 ASSIGNMENT STANDARD FOR ENGINE MODEL CODE
- 6.2 AUX. HYDRAULIC VALVE (DOUBLE ACTING VALVE)
- 2.4 AVOID FIRES
- 4.5 BACKLASH FOR DIFFERENTIAL PINION AND DIFFERENTIAL SIDE GEAR
- 4.1 BACKLASH FOR DIFFERENTIAL PINION AND SIDE GEAR
- 4.6 BACKLASH FOR SPIRAL BEVEL PINION AND 23 SPIRAL BEVEL GEAR
- 4.3 BACKLASH FOR SPIRAL BEVEL PINION AND RING GEAR
- 6.2 BEVEL Gearcase AND FRONT AXLE CASE DISASSEMBLY AND ASSEMBLY
- 5.5 BEVEL PINION SHAFT
- 4.5 BLEEDING AIR FROM HST COMPONENT
- 3.1 BODY AND POWER TRAIN SYSTEM
- 4.4 BRAKE COMPONENTS INSPECTION
- 5.1 BRAKE PEDAL
- 4.1 BRAKE PEDAL Freeplay
- 4.3 BRAKE PEDAL STOPPER
- 6.1 BRAKE SECTION DISASSEMBLY AND ASSEMBLY
- 4.17 BRAKE SWITCH
- 5.7 BUBBLE TEST FOR RADIATOR
- 6.8 CAMSHAFT
- 2.6 CAUTIONS FOR HIGH PRESSURE HOSES
- 2.5 CAUTIONS WHEN HANDLING THE BATTERY
- 2.12 CAUTIONS WHEN HANDLING TIRES
- 4.1 CHARGE RELIEF VALVE PRESSURE CHECK
- 3.5 CHARGE WARNING LAMP OPERATION
- 4.2 CLEARANCE OF BRAKE LAMP SWITCH
- 4.5 COMBINATION SWITCH
- 2.1 COMPONENT ARRANGEMENT
- 2.3 COMPONENTS
- 4.10 COOLANT TEMPERATURE SENSOR
- 3.3 COOLING SYSTEM
- 7.14 CRANK GEARS AND SHAFTS CHECK
- 7.18 CRANKSHAFT AND FLYWHEEL
- 2.2 CROSS SECTIONAL AREA OF WIRING
- 4.4 CRUISE MAGNETIC CLEARANCE
ADJUSTMENT (OPTIONAL)
- 5.5 CRUISE (OPTIONAL)
- 6.1 CYLINDER BLOCK
- 7.21 CYLINDER BORE CHECK
- 6.3 CYLINDER HEAD
- 7.6 CYLINDER HEAD
- 6.7 CYLINDER HEAD COVER
- 5.3 DIFFerential LOCK FORK
- 2.2 DIFFERENTIAL SYSTEM
- 5.6 DIFF. GEAR SHAFT
- 6.5 DISPLAY CONTROL
- 2.11 DISPOSAL OF ENVIRONMENTAL WASTE
- 7.1 DTC (DIAGNOSTIC TROUBLE CODE)
- 3.6 ECU OPERATION
- 2.5 ELECTRIC DEVICE DIAGNOSIS
- 6.1 ENGINE ELECTRICAL
- 6.6 ENGINE ELECTRICAL (3)
- 1.1 ENGINE EPA DECAL (A)
- 1.2 ENGINE NUMBER (B)
- 4.12 ENGINE OIL PRESSURE SWITCH
- 2.2 ENGINE PERFORMANCE CURVE
- 2.3 ENGINE PERFORMANCE CURVE ANALYSIS
- 3.2 ENGINE SERIAL NUMBER
- 6.14 ENGINE STOP LEVER
- 4.11 ENGINE STOP SOLENOID
- 5.5 EXTERNAL HYDRAULIC VALVE
- 5.1 FAN BELT
- 4.6 FLASHER UNIT
- 6.5 FLOW CONTROL VALVE
- 6.10 FLYWHEEL
- 7.20 FLYWHEEL AND CRANKSHAFT CHECK
- 5.3 FRONT AXLE
- 5.4 FRONT AXLE BRACKET
- 5.2 FRONT AXLE CASE
- 6.1 FRONT AXLE OIL SEAL REPLACEMENT
- 4.2 FRONT AXLE TOE-IN ADJUSTMENT
- 5.1 FRONT DIFFERENTIAL
- 6.4 FRONT DIFFERENTIAL SYSTEM DISASSEMBLY AND ASSEMBLY COMPONENTS
- 6.3 FRONT DIFFERENTIAL SYSTEM REMOVAL AND INSTALLATION
- 5.4 FRONT DRIVE FORK
- 5.1 FRONT DRIVE SYSTEM
- 2.5 FRONT WHEEL DRIVE SECTION
- 6.2 FRONT WHEEL DRIVE SECTION DISASSEMBLY
- 6.12 FUEL CAMSHAFT
- 7.13 FUEL CAMSHAFT
- 5.6 FUEL GAUGE OPERATION
- 4.14 FUEL SENDER
- 6.8 FUEL SENDER
- 3.4 FUEL SYSTEM
- 2.4 FUSE
- 4.1 FUSE
- 4.8 FUSE & RELAY BOX
- 6.1 GEAR ARRANGEMENT
- 7.10 Gearcase
- 6.4 GEARCASE
- 5.8 GEAR PUMP
- 1.1 GENERAL SPECIFICATIONs
- 2.1 GENERAL SPECIFICATIONS
- 1.1 GENERAL SPECIFICATIONS
- 1.1 GENERAL SPECIFICATIONS
- 1.1 GENERAL SPECIFICATIONS
- 1.1 GENERAL SPECIFICATIONS
- 8.1 GENERAL USE SCREWS, BOLTS, AND NUTS
- 6.7 GLOW CONTROL
- 4.9 GLOW PLUG
- 7.3 GLOW PLUG AND FUEL OVERFLOW PIPE
- 4.7 GLOW RELAY
- 6.15 GOVERNOR
- 3.5 GOVERNOR AND STOP SYSTEM
- 7.9 GOVERNOR SPRING AND STOP SOLENOID
- 2.8 HANDLING OF HAZARDOUS MATERIALS
- 2.9 HANDLING OF ROTATING BLADE, SHAFT AND DRIVING BELT
- 4.15 HAZARD WARNING LAMP SWITCH
- 7.2 HEAD COVER INSTALLATION
- 7.4 HEAT SEAL REMOVAL
- 5.9 HOUR METER OPERATION
- 4.2 HP RELIEF VALVE PRESSURE CHECK
- 1.2 HST
- 5.2 HST ASSY
- 6.2. HST COMPONENTS DISASSEMBLY AND ASSEMBLY
- 5.6 HST CONTROL
- 6.1. HST DISASSEMBLY AND ASSEMBLY
- 5.3 HST EXTERNAL HYDRAULIC LINE
- 4.3 HST NEUTRAL POSITION ADJUSTMENT
- 5.4 HST PEDAL
- 5.7 HST PROPER SHAFT
- 1.4 HST STRUCTURE & COMPONENTS
- 5.1 HYD. CYLINDER
- 5.3 HYDRAULIC 1
- 5.4 HYDRAULIC 2
- 6.7 HYDRAULIC BLOCK
- 5.6 HYDRAULIC BLOCK (T3)
- 6.3 HYDRAULIC CYLINDER
- 6.1 HYDRAULIC PUMP & HYDRAULIC FILTER REMOVAL AND REASSEMBLY
- 7.11 IDLE GEAR AND CRANK GEAR
- 4.2 IGNITION SWITCH
- 5.8 INJECTION NOZZLE INSPECTION
- 7.8 INJECTION PUMP
- 5.5 INJECTION TIMING MEASUREMENT AND ADJUSTMENT
- 4.2 INSPECTION USING EXTERNAL HYDRAULIC VALVE COUPLER
- 4.25 INSTRUMENT PANEL
- 7.7 INTAKE AND EXHAUST VALVES
- 4.26 LAMPS
- 4.3 LEVER SETTING OF HYDRAULIC LIFT CYLINDER
- 5.2 LIFT CONTROL VALVE
- 6.4 LIFT CONTROL VALVE
- 6.3 LIGHT CONTROL
- 6.8 LOADER JOYSTICK VALVE
- 2.3 LOAD TRANSFER
- 3.2 LUBRICATING SYSTEM
- 7.2 LUBRICATION LIST
- 6.5 MAIN BEARING CASE
- 2.1 MAIN GEAR SHIFT SECTION
- 5.6 MAIN SHAFT
- 7.1 MAINTENANCE SCHEDULE
- 1.3 MAJOR TIGHTENING TORQUE
- 6.19 MANIFOLD
- 7.19 METAL JOURNAL BEARINGS
- 6.11 NOZZLE HOLDER
- 6.2 OIL PAN
- 5.6 OIL PRESSURE MEASUREMENT
- 7.22 OIL PUMP, OIL FILTER, RELIEF VALVE AND OIL STRAINER
- 4.20 ONE SIDE BRAKE SWITCH
- 2.1 OPERATING DIAGRAM
- 2.2 OPERATING PRINCIPLE
- 3.3 OPERATING PRINCIPLE OF PREHEAT
- 2.3 OPERATING PRINCIPLE OF STEERING SYSTEM
- 2.2 OPERATING PRINCIPLE OF SYNCHRONIZER
- 2.2 OPERATION OF HST
- 4.18 PARKING BRAKE MICRO SWITCH
- 3.6 PCV VALVE
- 7.1 PCV VALVE
- 4.13 PICKUP SENSOR
- 7.15 PISTON AND CONNECTING ROD
- 7.16 PISTON AND CONNECTING ROD CHECK
- 5.2 PISTON COMPRESSION PRESSURE MEASUREMENT
- 6.9 PISTON CRANKSHAFT
- 7.17 PISTON RING MEASUREMENT
- 5.2 POWER STEERING CYLINDER
- 2.1 POWER TRAIN OF REAR AXLE
- 2.1 POWER TRANSFER SYSTEM FOR FRONT AXLE
- 4.23 PREHEAT CONTROLLER [AU, TH]
- 4.2 PRELOAD OF TAPER ROLLER BEARING IN DIFF.
- 4.4 PRELOAD OF TAPER ROLLER BEARING ON SPIRAL BEVEL PINION SHAFT
- 2.10 PREVENTION OF SCALD
- 2.2 PRINCIPLE OF DIFFERENTIAL SYSTEM
- 6.9 PTO CONTROL
- 5.9 PTO DRIVE SHAFT
- 2.4 PTO GEAR SHIFT SECTION
- 4.21 PTO SAFETY SWITCH
- 5.5 PTO SHAFT
- 6.4 PTO SHAFT DISASSEMBLY
- 5.3 PTO SHIFT FORK
- 5.2 RANGE FORK
- 5.8 RANGE SHAFT
- 2.3 RANGE SHIFT SECTION
- 5.4 REAR AXLE
- 6.1 REAR AXLE COMPONENTS
- 6.2 REAR DIFFERENTIAL DISASSEMBLY
- 5.2 REAR DIFFERENTIAL SYSTEM
- 6.6 RELIEF VALVE
- 7.5 ROCKER ARM ASSEMBLY
- 2.1 SAFETY GEAR
- 2.3 SAFETY INSTRUCTIONS WHEN PREPARING TRACTOR
- 4.19 SAFETY START SWITCH
- 1.2 SEALANT AND ADHESIVE
- 1.3 SEALANT AND ADHESIVE SPECIFICATIONS
- 4.24 SEAT SWITCH
- 4.16 SENSORS AND RELAYS
- 2.4 SERVICING SPECIFICATIONS
- 4.4 SETTING THE JOYSTICK LEVER
- 9.2 SNAP RING INSTALLATION
- 1.1 SPECIFICATIONS FOR STEERING SYSTEM
- 6.13 SPEED CONTROL PLATE
- 5.1 SPIRAL BEVEL GEAR
- 9.1 SPRING PIN TYPE
- 6.2 START CONTROL
- 4.3 START MOTOR
- 4.2 STEERING ANGLE
- 5.3 STEERING COLUMN
- 5.1 STEERING CYLINDER
- 6.2 STEERING CYLINDER REMOVAL
- 2.2 STEERING UNIT
- 4.1 STEERING UNIT RELIEF PRESSURE INSPECTION
- 4.1 STEERING UNIT RELIEF VALVE PRESSURE CHECK
- 6.1 STEERING UNIT REMOVAL
- 2.1 STRUCTURE AND FUNCTION OF HST
- 2.4 STRUCTURE AND OPERATING PRINCIPLE
- 8.2 STUD BOLTS
- 5.7 SUCTION PIPE GROUP (T4)
- 4.3 SWAY RESISTANCE
- 4.22 SWITCHS
- 2.3 SYMBOLS FOR ELECTRIC COMPONENTS
- 3.1 SYNCHRONIZER GEAR INSPECTION
- 5.8 TACHOMETER OPERATION WITH THE ENGINE RUNNING
- 5.7 TEMPERATURE GAUGE OPERATION
- 7.23 THERMOSTAT
- 1.2 TIGHTENING TORQUE
- 1.2 TIGHTENING TORQUE FOR MAJOR COMPONENTS
- 1.3 TIGHTENING TORQUE FOR MAJOR COMPONENTS
- 1.2 TIGHTENING TORQUE FOR MAJOR COMPONENTS
- 1.2 TIGHTENING TORQUES
- 4.1 TOE-IN
- 4.8 TOOTH CONTACT FOR UPPER BEVEL GEARS AND FINAL DRIVE BEVEL GEARS
- 4.4 TOOTH CONTACT OF SPIRAL BEVEL
- 4.7 TOOTH CONTACT OF SPIRAL BEVEL GEAR
- 3.1 TRACTOR SERIAL NUMBER
- 5.1 TRANSMISSION CASE
- 6.1 TRANSMISSION CASE MAIN SHIFT, RANGE SHIFT SECTION DISASSEMBLY
- 6.3 TRANSMISSION CASE SHIFT SECTION ASSEMBLY
- 1.1 TRANSMISSION FLUID
- 3.3 TRANSMISSION SERIAL NUMBER
- 2.7 USE OF APPROPRIATE TOOLS AND EQUIPMENT
- 7.12 VALVE CAMSHAFT
- 5.3 VALVE CLEARANCE
- 5.4 VALVE LIFT (DEFLECTION AND WORN CONDITION OF VALVE CAM, TAPPET, PUSH ROD, ROCKER ARM, ETC.)
- 6.6 VALVE ROCKER ARM
- 6.17 WATER HOSE
- 6.16 WATER PUMP
- 7.24 WATER PUMP
- 3.1 WHEN IGNITION SWITCH IS IN “OFF” POSITION
- 3.2 WHEN IGNITION SWITCH IS TURNED TO "ACC" POSITION
- 3.4 WHEN IGNITION SWITCH IS TURNED TO "ST" POSITION
- 5.1 WHEN THE ENGINE CANNOT BE STARTED
- 5.5 WHEN THE HEAD LAMP CANNOT BE OPERATED
- 5.2 WHEN THE SYSTEM IS NOT CHARGED
- 5.4 WHEN THE SYSTEM IS NOT PREHEATED AUTOMATICALLY
- 5.3 WHEN THE SYSTEM IS NOT PREHEATED MANUALLY
- 6.4 WIRE HARNESS
- 2.1 WIRING COLOR IDENTIFICATION
- 2.2 WORK PLACE
Bobcat Software
Bobcat PDF Manuals
