Tadano TM-2000-1 Boom Truck Full Manual (Operator, Parts, Service)

Table of Contents:

Operator Manual Table of Contents

1,014 pages, 13 files

• Manual 5 (267 pages)
  • STANDARD COMPONENTS
  • MINIMUM TRUCK REQUIREMENTS
  • MOUNTING CONFIGURATIONS
  • PTO HORSEPOWER REQUIREMENTS
  • PTO SELECTION
  • PUMP INSTALLATION
  • COUNTERWEIGHTING
  • CRANE INSTALLATION
  • HYDRAULIC OL TANK INSTALLATION
  • BOOM REST INSTALLATION
  • PIPING (HYDRAULIC PUMP-HYDRAULIC OlL TANK-CONTROL VALVE)
  • OUTRIGGER INSTALLATION
  • REAR STABILIZER INSTALLATION
  • FRONT STABILIZER INSTALLATION
  • BOOM INSTALLATION
  • ENGINE CONTROL
  • BUBBLE LEVEL ADJUSTMENT
  • AFFIXING INFORMATION DECALS
  • AMA ADJUSTMENT
  • OPTION
  • Boom angle restriction system
  • Radio control system
  • Rotary joint
  • INITIAL CRANE START-UP PROCEDURE
  • FINAL TEST AND INSPECTION
  • INSPECTION POINT
  • MOUNTING REPORT
  • CRANE WEIGHT AND DIMENSIONS
• Publication TM-2000-1-01(U)-1E / Serial No. EX0069 and up, EX0109 (149 pages)
  • Before Operation
  • Rules for Operation (Outriggers, Stabilizers)
  • Rules for Operation (General)
  • Rules for Operation (Weather)
  • Rules for Operation (Power Lines, Radio Waves)
  • After Operation
  • Rules for Traveling on Roads
  • Rules for Inspection and Maintenance
  • Warning Decals – Location and Contents
• Publication TM-2000-1-01(U)-2E / Serial No. EX0069 and up, EX0109 (149 pages)
• Publication TM-2000-1-02(U)-2E / Serial No. EX0142 and later (149 pages)

  Same chapters as the edition above (another edition or language of this manual).

• Manual 4 (2 pages)
• Manual 6 (149 pages)
• Manual 7 (149 pages)

Parts Manual Table of Contents

1,265 pages, 11 files

• Publication TM-2000-1_PD2(U)-2EJ / Serial No. EX0142 and up (278 pages)
• Publication TM-2000-1-P1(U)-1EJ / Serial No. EX0109 (243 pages)
  • Telescoping System
  • Hydraulic Pressure
  • Outrigger System
  • Gear Drive
  • Piping Swing
  • Cylinder Elevating
  • Piping Elevating
  • Winch System
  • Cylinder Telescoping
  • Cover Swing
  • Mounting Cab
• Publication TM-20110 / Serial No. EX0142 (422 pages)
  • Boom
  • Mounting Parts
  • Gear System
  • Indication Plates
  • Outrigger System
  • Options
  • Outrigger Gear
  • Rope Wire
  • Piping Telescoping
  • Cover Bearing
  • Swing Frame
  • Cylinder Elevating
  • Step
  • Piping Upper
  • Piping Lower
• Publication TM-2000-1_PD1(U)-2EJ (315 pages)
  • TM-2000-1, NORTH AMERICA – SYSTEM index
  • POWER TAKE OFF & PUMP
  • OUTRIGGER SYSTEM
  • BOOM UNIT
  • FRAME UNIT
  • INDICATION PLATES
  • REMOTE CONTROL SYSTEM
  • MOUNTING PARTS
  • OPTIONS
• Serial No. EX0109 and up (7 pages)

Service Manual Table of Contents

250 pages, 2 files

• Publication TM-2000-1-S1(U)-1E / Serial No. EX0069 (192 pages)
  • Foreword
    • Applicable unit No
    • Separate service manual
    • Outline of specifications
  • (B) Hydraulic Power Generating System
    • high/low shift)
    • B-2 Manual Control Valve (Outrigger)
    • B-3 Manual Control valve (Winch)
  • (C) Outrigger System
    • C-1 Jack Cylinder (Front and rear stabilizer)
    • C-2 Jack Cylinder
    • C-3 Pilot Check Valve (Front and rear stabilizer)
  • (D) Swing System
    • D-1 Hydraulic Motor (Swing)
    • D-2 Swing Speed Reducer
    • D-3 Swing Bearing
  • (E) Boom Elevating System
    • E-1 Boom Elevating Cylinder
    • E-2 Counterbalance Valve (Elevating)
  • (F) Winch System
    • F-1 Winch
    • F-2 Hydraulic Motor(Winch)
    • F-3 Counterbalance Valve(Winch)
  • (G) Boom Telescoping System
    • G-1 General description of telescoping system
    • G-2 Boom (Five-section boom)
    • G-3 Telescoping Cylinder
  • (H) Safety System
    • H-1 AMA (Load Moment Indicator)
    • H-2 Boom Length/Angle Detector
    • H-3 Outrigger Extension Detector
  • (V) Remote Control System
    • V-1 Configurations of Radio-control System
    • V-2 Radio-control Valve
    • V-3 Accelerator Cylinder
  • (Y) Data, Adjustment and Checks
    • Y-1 Service Data
    • Y-2 Adjustment and Checks
  • (Z) System Diagrams
    • 414 ( Radio-controls spec.)
    • Z-7 Location of Hydraulic Parts
    • Z-8 Location of Electrical Parts
  • History of revision
• Publication SA01-01-2E (58 pages)
  • Foreword
    • 1.Contents
    • 2.Conversion
  • Contents of Information
    • 1.Basic Cautions
  • Hydraulic System Troubleshooting
    • 1.Actuator malfunction
    • 2.Noise and vibration
    • 3.Oil heating
  • Dismounting and Remounting
  • Disassembly and Reassembly
    • 1.Cylinder
    • 2.Valve
  • Sealing Parts
    • 1.Packing
    • 3.Backup ring
    • 4.Seal ring
  • Piping Procedure
    • 1.How to apply seal tape
    • 2.Screwing R fittings
    • 3.Connecting high-pressure hoses
  • Machine Elements
    • 1.Bolt, nut
    • 2.Bearing
    • 3.Wire rope
  • Hydraulic Oil
    • 1.Hydraulic oil control
    • 2.Evaluating oil deterioration and contamination
    • 3.Hydraulic oil changing procedure
  • History of revision

Also in this set

• Assembly and installation (3 files, 790 pages)